Dell OptiPlex 760 Скачать руководство пользователя страница 126

Страница: 126 / 203

Optical Drive

Removing an Optical Drive

Follow the procedures in

Working on Your Computer

Remove the computer cover (see

Removing the Computer Cover

Pull the drive release latch and slide the drive towards the back of the computer. Then lift up to remove the drive from the computer.

Disconnect the power and data cable from the back of the drive.

Disconnect the data cable from the system board.

WARNING:

Before working inside your computer, read the safety information that shipped with your computer. For additional safety best

practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.

WARNING:

To guard against electrical shock, always unplug your computer from the electrical outlet before removing the computer cover.

CAUTION:

Do not pull the drive out of the computer by the drive cables. Doing so may cause damage to cables and the cable connectors.

1 drive release latch 2 optical drive

1 optical drive 2 data cable

3 power cable

Содержание OptiPlex 760












































































































































































































Результаты поиска

Содержание OptiPlex 760

Отзывы:

Похожие инструкции для OptiPlex 760

Бренды по названию

Популярные бренды

Dell OptiPlex 760, Руководство по обслуживанию

Результаты поиска

Содержание OptiPlex 760

Отзывы:

Похожие инструкции для OptiPlex 760

Бренды по названию

Популярные бренды