Dell OptiPlex 760 Скачать руководство пользователя страница 70

Страница: 70 / 203

Back to Contents Page

Dell™ OptiPlex™ 760 Service Manual

Cards

Cards

Your Dell™ computer supports a PS/2 serial port adapter and provides the following connectors for PCI and PCI Express cards:

Two PCI card slots

One PCI Express x16 card slot

One PCI Express x1 card slot

Installing a PCI or PCI Express Card

If you are replacing a card, uninstall the driver for the existing card. See the documentation that came with the card for instructions.

Follow the procedures in

Working on Your Computer

Remove the computer cover (see

Removing the Computer Cover

Gently push the release tab on the card retention latch from the inside to pivot the latch open. The latch will remain in the open position.

WARNING:

Before working inside your computer, read the safety information that shipped with your computer. For additional safety best

practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.

CAUTION:

To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of

your computer's electronic components. You can do so by touching an unpainted metal surface on the computer chassis.

NOTE:

Installing filler brackets over empty card-slot openings is necessary to maintain FCC certification of the computer. The brackets keep dust and dirt

out of your computer and maintains the airflow that cools your computer.

1 PCI Express x16 card

2 securing tab (only for PCI Express cards)

3 PCI Express x16 card slot 4 PCI Express x1 card

5 PCI Express x1 card slot

NOTE:

Your Dell computer uses only PCI and PCI Express slots.

NOTE:

The serial port adapter for your mini tower computer includes two PS/2 connectors.

Содержание OptiPlex 760












































































































































































































Результаты поиска

Содержание OptiPlex 760

Отзывы:

Dell OptiPlex 760, Руководство по обслуживанию, Страница: 70 / 203

Результаты поиска

Содержание OptiPlex 760

Отзывы: