Dell OptiPlex 760 Скачать руководство пользователя страница 191 | Manualshive

Страница: 191 / 203

background image

When connecting and disconnecting a SATA data cable, hold the cable by the black connector at each end. When removing a cable with a pull-tab, grasp the
colored pull-tab and pull until the connector detaches.

Hard Drive

Removing the Hard Drive

1.

Follow the procedures in

Working on Your Computer

.

2.

Remove the computer cover (see

Removing the Computer Cover

).

3.

Disconnect the power and data cables from the hard drive.

4.

Press the plastic drive rails towards each other and slide the drive slightly forward.

5.

Rotate the hard drive up and away from the computer.

Installing a Hard Drive

1.

Follow the procedures in

Working on Your Computer

.

WARNING:

Before working inside your computer, read the safety information that shipped with your computer. For additional safety best

practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.

WARNING:

To guard against electrical shock, always unplug your computer from the power supply before removing the hard drive.

CAUTION:

To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of

your computer's electronic components. You can do so by touching an unpainted metal surface on the computer chassis.

CAUTION:

To avoid damage to the drive, do not set it on a hard surface. Instead, set the drive on a surface, such as a foam pad, that will

sufficiently cushion it.

1 hard drive

2 drive rails (2)

3 data cable connector 4 power cable connector

«
...
189
190
191
192
193
...
»

Содержание OptiPlex 760












































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для OptiPlex 760

Color Computer 3 Basic

Бренд: Tandy Страницы: 17

TRS-80 Model II

Бренд: Tandy Страницы: 36

Бренд: Tandy Страницы: 337

Бренд: Tandy Страницы: 251

Бренд: Medion Страницы: 2

Бренд: Barco Страницы: 2

ECLIPSE MV/7800

Бренд: Data General Service Страницы: 167

Бренд: HP Страницы: 53

Бренд: Honeywell Страницы: 100

Бренд: HP Страницы: 66

Бренд: HP Страницы: 28

Бренд: Beckman Instruments Страницы: 80

Бренд: FabiaTech Страницы: 3

Бренд: FabiaTech Страницы: 4

Direct Linear DV-7DL Pro

Бренд: Edirol Страницы: 372

XPC slim DL10J Series

Бренд: Shuttle Страницы: 25

Бренд: IEI Technology Страницы: 14

Бренд: Aplex Страницы: 69

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды