manualshive.com logo in svg

Dell OptiPlex 760, Руководство по обслуживанию

Характеристики Dell OptiPlex 760 доступны для скачивания бесплатно на manualshive.com. Здесь вы сможете получить подробное руководство пользователя с описанием всех функций и характеристик этого продукта. Узнайте больше о вашем устройстве, загрузив руководство на manualshive.com.

Поделиться
Скачать
background image

Back to Contents Page

  

 

 Battery  

Dell™ OptiPlex™ 760 Service Manual 

 

  

Replacing the Battery 

 

 

 

Replacing the Battery  

 

 

 

 

A coin-cell battery maintains computer configuration, date, and time information. The battery can last several years. 

The battery may need replacing if an incorrect time or date is displayed during the boot routine along with a message such as: 

Time-of-day not set - please run SETUP program 

or 

Invalid configuration information -  

please run SETUP program 

or 

Strike the F1 key to continue, 

F2 to run the setup utility 

To determine whether you need to replace the battery, reenter the time and date in system setup and exit the program to save the information. Turn off your 
computer and disconnect it from the electrical outlet for a few hours; then reconnect the computer, turn it on, and enter system setup (see 

Entering System 

Setup

). If the date and time are not correct in system setup, replace the battery. 

You can operate your computer without a battery; however, without a battery, the configuration information is erased if the computer is turned off or 
unplugged from the electrical outlet. In this case, you must enter system setup (see 

Entering System Setup

) and reset the configuration options. 

 

 

To remove the battery: 

 

 

1.

If you have not already done so, make a copy of your configuration information, found in system setup.  
 

 

  

2.

Follow the procedures in 

Working on Your Computer

.  

 

 

  

3.

Remove the computer cover.  
 

 

  

4.

Locate the battery socket.  
 

 

 

 

 

 

 

5.

Remove the system battery.  
 

a.

 

Support the battery connector by pressing down firmly on the positive side of the connector.  

 

b.

 

While supporting the battery connector, press the battery tab away from the positive side of the connector and pry the battery it up out of the 

securing tabs at the negative side of the connector.  
 

 

WARNING: 

Before working inside your computer, read the safety information that shipped with your computer. For additional safety best 

practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance. 

 

CAUTION: 

To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of 

your computer's electronic components. You can do so by touching an unpainted metal surface on the computer chassis.

 

WARNING: 

A new battery can explode if it is incorrectly installed. Replace the battery only with the same or equivalent type recommended by the 

manufacturer. Discard used batteries according to the manufacturer's instructions. 

 

CAUTION: 

If you pry the battery out of its socket with a blunt object, be careful not to touch the system board with the object. Ensure that the 

object is inserted between the battery and the socket before you attempt to pry out the battery. Otherwise, you may damage the system board by 
prying off the socket or by breaking circuit traces on the system board.

 

CAUTION: 

To avoid damage to the battery connector, you must firmly support the connector while removing the battery. 

Содержание OptiPlex 760












































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для OptiPlex 760

Contec PT-970 A Series Reference Manual preview
PT-970 A Series
Бренд: Contec Страницы: 77
Knoll Pixel Y-Leg Installation Instructions preview
Pixel Y-Leg
Бренд: Knoll Страницы: 2
IBASE Technology MPT-1000R User Manual preview
MPT-1000R
Бренд: IBASE Technology Страницы: 80
Psion Teklogix Vehicle-Mount Computer 8515 User Manual preview
Vehicle-Mount Computer 8515
Бренд: Psion Teklogix Страницы: 190
IBM IntelliStation Z Pro Type 6866 User Manual preview
IntelliStation Z Pro Type 6866
Бренд: IBM Страницы: 194
Epson ActionDesk 4000 Specifications preview
ActionDesk 4000
Бренд: Epson Страницы: 11
Epson ActionPC 7000 Product Information Manual preview
ActionPC 7000
Бренд: Epson Страницы: 10
Epson ActionTower 2000 User Manual preview
ActionTower 2000
Бренд: Epson Страницы: 131
Epson ActionPC 6000 User Manual preview
ActionPC 6000
Бренд: Epson Страницы: 144
Epson ActionPC 3000 User Manual preview
ActionPC 3000
Бренд: Epson Страницы: 131
Epson ActionPC 2000 User Manual preview
ActionPC 2000
Бренд: Epson Страницы: 129
Epson ActionPC 5500 User Manual preview
ActionPC 5500
Бренд: Epson Страницы: 147
Epson ActionDesk 4000 User Manual preview
ActionDesk 4000
Бренд: Epson Страницы: 163
Epson ActionPC 2600 User Manual preview
ActionPC 2600
Бренд: Epson Страницы: 147
Epson ActionPC 8000 User Manual preview
ActionPC 8000
Бренд: Epson Страницы: 187
Epson 486SX User Manual preview
486SX
Бренд: Epson Страницы: 233
Epson ActionPC 7300 User Manual preview
ActionPC 7300
Бренд: Epson Страницы: 196
Epson ActionPC 1500 Reference Manual preview
ActionPC 1500
Бренд: Epson Страницы: 272

Бренды по названию

Популярные бренды

Загрузить еще бренды