Dell OptiPlex 760 Скачать руководство пользователя страница 159

Страница: 159 / 203

13.

Assign a new system and/or administrator password.

Clearing CMOS Settings

Follow the procedures in

Working on Your Computer

Remove the computer cover.

Reset the current CMOS settings:

Locate the password (PSWD) and CMOS (RTCRST) jumpers on the system board (see

Password Protection

Remove the password jumper plug from its pins.

Place the password jumper plug on the RTCRST pins and wait approximately 5 seconds.

Remove the jumper plug from the RTCRST pins and place it back on the password pins.

Replace the computer cover (see

Replacing the Computer Cover

Connect your computer and devices to electrical outlets, and turn them on.

Deploying Citrix

Provisioning Server (Dell) With Client Static IP Configuration

In a secure environment where no DHCP service exists to assign IP addresses to clients and allow the clients to boot to the Provisioning Server, manually
program static IP addresses for those clients in the system BIOS:

During boot, press <F2> to open System Setup.

Select

ImageSever

from the list of boot options.

Set

Client DHCP

Static IP.

Select

Accept

in the window that opens asking you to confirm changing the Client DHCP option.

Set the

Client IP

with your desired IP address. The default is 255.255.255.255.

Set the

Client Subnet Mask

to the address assigned to the client. The default address is 255.255.255.255.

Set the

Client Gateway

to the gateway address assigned to the client. The default address is 255.255.255.255.

Change the

Lookup Method

Static IP

Set the

ImageServer IP

with the primary Provisioning Server IP address. The default address is 255.255.255.255.

10.

Save the settings and reboot the system.

Back to Contents Page

NOTE:

This procedure enables the password feature. When you enter system setup (see

Entering System Setup

), both system and administrator

password options appear as

Not Set

—

meaning that the password feature is enabled but no password is assigned.

WARNING:

Before working inside your computer, read the safety information that shipped with your computer. For additional safety best

practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.

CAUTION:

To connect a network cable, first plug the cable into the network wall jack and then plug it into the computer.

Содержание OptiPlex 760












































































































































































































Результаты поиска

Содержание OptiPlex 760

Отзывы:

Похожие инструкции для OptiPlex 760

Бренды по названию

Популярные бренды

Dell OptiPlex 760, Руководство по обслуживанию

Результаты поиска

Содержание OptiPlex 760

Отзывы:

Похожие инструкции для OptiPlex 760

Бренды по названию

Популярные бренды