manualshive.com logo in svg

Dell OptiPlex 760, Руководство по обслуживанию, Страница: 105 / 203

Поделиться
Скачать
Dell OptiPlex 760 Скачать руководство пользователя страница 105

Back to Contents Page

  

 

 Replacing the Computer Cover  

Dell™ OptiPlex™ 760 Service Manual 

 

  

Mini-Tower, Desktop, and Small Form Factor 

 

  

Ultra Small Form Factor 

 

 

 

 

 

 

 

Mini-Tower, Desktop, and Small Form Factor  

 

 

1.

Ensure that all cables are connected, and fold cables out of the way.  
 

Gently pull the power cables toward you so that they do not get caught underneath the drives. 

 

 

2.

Ensure that no tools or extra parts are left inside the computer.  
 

 

  

3.

To replace the cover:  
 

a.

 

Align the bottom of the cover with the hinge tabs located along the bottom edge of the computer.  

 

b.

 

Using the hinge tabs as leverage, rotate the cover downward to close it.  

 

c.

 

Snap the cover into place by pulling back on the cover release latch and then releasing the latch when the cover is properly seated.  

 

d.

 

Ensure that the cover is seated correctly before moving the computer.  

 

 

 

 

 

4.

Attach the computer stand (if applicable). For instructions, see the documentation that came with the stand.  
 

 

  

5.

Connect your computer and devices to electrical outlets, and turn them on.  
 

After you remove and replace the cover, the chassis intrusion detector (optional on some computers), if installed and enabled, causes the following 
message to appear on the screen at the next computer start-up: 

ALERT! Cover was previously removed. 

 

 

6.

Reset the chassis intrusion detector in 

System Setup

 by changing 

Chassis Intrusio

n to 

On

 or 

On-Silent

.  

 

 

Ultra Small Form Factor  

 

 

1.

Follow the procedures in 

Working on Your Computer

.  

 

 

 

 

 

2.

If applicable, remove the cable cover (see 

Removing the Cable Cover

).  

 

 

  

3.

Replace the computer cover:  
 

a.

 

Tilting the cover slightly, align it with the retaining strip at the back of the system.  

 

b.

 

Slide the computer cover backward until it snaps into place.  

 

 

 

 

WARNING: 

Before working inside your computer, read the safety information that shipped with your computer. For additional safety best 

practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance. 

 

CAUTION: 

To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of 

your computer's electronic components. You can do so by touching an unpainted metal surface on the computer chassis.

 

CAUTION: 

To connect a network cable, first plug the cable into the network wall jack and then plug it into the computer.

 

NOTE: 

If an administrator password has been assigned by someone else, contact your network administrator for information on resetting the chassis 

intrusion detector.

 

CAUTION: 

Before touching anything inside your computer, ground yourself by touching an unpainted metal surface. While you work, periodically 

touch an unpainted metal surface to dissipate any static electricity that could harm internal components.

 

WARNING: 

Graphics card heat sinks can become very hot during normal operation. Ensure that a graphics card heat sink has had sufficient time 

to cool before you touch it. 

Содержание OptiPlex 760












































































































































































































Отзывы:

Нет отзывов