manualshive.com logo in svg

Dell OptiPlex 760, Руководство по обслуживанию, Страница: 108 / 203

Поделиться
Скачать
Dell OptiPlex 760 Скачать руководство пользователя страница 108

4.

If you are installing a new card, remove the filler bracket to create a card- slot opening. Then continue with 

step 6

.  

 

 

  

5.

If you are replacing a card that is already installed in the computer, remove the card. If necessary, disconnect any cables connected to the card. Then 
continue with 

step 6

.  

 

 

  

6.

Prepare the card for installation.  
 

 

 

 

 

7.

Place the card in the connector and press down firmly. Ensure that the card is fully seated in the slot.  
 

  

 

 

8.

Before closing the card retention latch, ensure that:  
 

l

 

The tops of all cards and filler brackets are flush with the alignment guide 

 

l

 

The notch in the top of the card or filler bracket fits around the alignment guide 

 

 

  

9.

Secure the card(s) by closing the card retention latch and snapping it into place.  
 

 

 

 

 

10.

Connect any cables that should be attached to the card.  
 

 

  

11.

Replace the computer cover (see 

Replacing the Computer Cover

).  

 

 

 

12.

If you installed a sound card:  
 

a.

 

Enter system setup, select 

System Configuration

®

 

Miscellaneous Devices

, and change the 

Audio

 setting to 

Disabled 

(see 

Entering System 

Setup

).  

 

b.

 

Connect external audio devices to the sound card's connectors. Do not connect external audio devices to the microphone, speaker/headphone, 

or line-in connectors on the back panel of the computer.  
 

 

 

 

 

13.

If you installed a network adapter card and want to turn off the integrated network adapter:  
 

a.

 

Enter system setup, select 

System Configuration

®

 

Integrated NIC

, and change the setting to 

Disabled

 (see 

Entering System Setup

).  

 

 

 

b.

 

Connect the network cable to the network adapter card's connectors. Do not connect the network cable to the integrated network connector on 

the back panel of the computer.  
 

 

 

 

WARNING: 

Some network adapters automatically start the computer when they are connected to a network. To guard against electrical shock, be 

sure to unplug your computer from its electrical outlet before installing any cards. 

 

NOTE: 

See the documentation that came with the card for information on configuring the card, making internal connections, or customizing it for 

your computer.

1 

card fully seated 

2 

card not fully seated  

3 

bracket within slot 

4 

bracket caught outside of slot 

 

CAUTION: 

Do not route card cables over the cards. Cables routed over the cards can prevent the computer cover from closing properly or cause 

damage to the equipment.

 

NOTE: 

See the documentation that came with the card regarding the card's cable connections.

 

CAUTION: 

If you disable the integrated network adapter, you will not have AMT functionality.

 

CAUTION: 

To connect a network cable, first plug the cable into the network wall jack and then plug it into the computer.

Содержание OptiPlex 760












































































































































































































Отзывы:

Нет отзывов