Dell OptiPlex 760 Скачать руководство пользователя страница 111

Страница: 111 / 203

Connect any cables that should be attached to the card.

Before you close the card retention mechanism, ensure that:

The tops of all cards and filler brackets are flush with the alignment bar.

The notch in the top of the card or filler bracket fits around the alignment guide.

10.

Secure the card(s) by closing the card retention latch and snapping it into place.

11.

Replace the computer cover (see

Replacing the Computer Cover

12.

If you installed a sound card:

Enter system setup, select

System Configuration

Miscellaneous Devices

, and change the

Audio

setting to

Disabled.

(See

Entering System

Setup

Connect external audio devices to the sound card's connectors. Do not connect external audio devices to the microphone, speaker/headphone,

or line-in connectors on the back panel of the computer.

13.

If you installed a network adapter card and want to turn off the integrated network adapter:

Enter system setup, select

System Configuration

Integrated NIC

, and change the setting to

Disabled

. (See

Entering System Setup

Connect the network cable to the network adapter card's connectors. Do not connect the network cable to the integrated network connector on

the back panel of the computer.

14.

Install any drivers required for the card as described in the card documentation.

Removing a PCI Express x16 Card or DVI Card

Follow the procedures in

Working on Your Computer

Remove the computer cover (see

Removing the Computer Cover

Gently lift the release tab on the card retention latch from the inside and pivot the latch open.

PCI Express x16 card connector

card fully seated

card not fully seated

bracket within slot

bracket caught outside of slot

CAUTION:

Do not route card cables over the cards. Cables routed over the cards can prevent the computer cover from closing properly or cause

damage to the equipment.

NOTE:

See the documentation for the card for information about the card's cable connections.

CAUTION:

If you disable the integrated network adapter, you will not have AMT functionality.

CAUTION:

To connect a network cable, first plug the cable into the network wall jack and then plug it into the computer.

Содержание OptiPlex 760












































































































































































































Результаты поиска

Содержание OptiPlex 760

Отзывы:

Похожие инструкции для OptiPlex 760

Бренды по названию

Популярные бренды

Dell OptiPlex 760, Руководство по обслуживанию

Результаты поиска

Содержание OptiPlex 760

Отзывы:

Похожие инструкции для OptiPlex 760

Бренды по названию

Популярные бренды