Dell OptiPlex 760 Скачать руководство пользователя страница 37

Страница: 37 / 203

Disconnect the power and data cables from the back of the floppy drive.

If you are not replacing the floppy drive or media card reader at this time, install the floppy drive inserts (see

Replacing Drive Inserts

). Contact Dell if you

need a drive bay insert.

Installing a Floppy Drive

If you are installing a new floppy drive

Remove the drive inserts (see

Removing Drive Inserts

Pull to remove the floppy drive insert that should be installed in the drive bay.

Remove the four shoulder screws from the drive panel insert.

If you are replacing an existing floppy drive:

Remove the four shoulder screws from the existing drive or media card reader.

Insert the four shoulder screws into the sides of the new floppy drive and tighten them.

1 drive release latch 2 floppy drive

1 drive insert

Содержание OptiPlex 760












































































































































































































Результаты поиска

Содержание OptiPlex 760

Отзывы:

Dell OptiPlex 760, Руководство по обслуживанию, Страница: 37 / 203

Результаты поиска

Содержание OptiPlex 760

Отзывы: