manualshive.com logo in svg

Dell OptiPlex 760, Руководство по обслуживанию

Характеристики Dell OptiPlex 760 доступны для скачивания бесплатно на manualshive.com. Здесь вы сможете получить подробное руководство пользователя с описанием всех функций и характеристик этого продукта. Узнайте больше о вашем устройстве, загрузив руководство на manualshive.com.

Поделиться
Скачать
background image

Back to Contents Page

  

 

 Working on Your Computer  

Dell™ OptiPlex™ 760 Service Manual 

 

  

Recommended Tools 

 

  

Before Working on Your Computer 

 

  

After Working on Your Computer 

 

 
This document provides procedures for removing and installing the components in your computer. Unless otherwise noted, each procedure assumes that: 

l

 

You have performed the steps in this section. 

 

l

 

You have read the safety information that shipped with your computer. 

 

l

 

When replacing a component, you have already removed the original, if installed. 

 

 

Recommended Tools  

The procedures in this document may require the following tools: 

l

 

Small flat-blade screwdriver 

 

l

 

Phillips screwdriver 

 

l

 

Small plastic scribe 

 

l

 

Flash BIOS update (see the Dell Support website at 

support.dell.com

) 

 

 

Before Working on Your Computer  

Use the following safety guidelines to help protect your computer from potential damage and to help ensure your own personal safety. 

 

 

 

 

 

 

 

 

 

 

1.

Ensure that the work surface is flat and clean to prevent the computer cover from being scratched.  
 

 

  

2.

Turn off your computer (see 

Turning Off Your Computer

).  

 

 

 

 

 

3.

Disconnect all telephone or network cables from the computer.  
 

 

  

4.

Disconnect your computer and all attached devices from their electrical outlets.  
 

 

  

5.

Press and hold the power button while the system is unplugged to ground the system board.  
 

 

 

 

 

Turning Off Your Computer 

 

 

 

NOTE: 

The color of your computer and certain components may appear differently than shown in this document.

 

WARNING: 

Before working inside your computer, read the safety information that shipped with your computer. For additional safety best 

practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance. 

 

CAUTION: 

Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell is 

not covered by your warranty.

 

CAUTION: 

When you disconnect a cable, pull on its connector or on its pull-tab, not on the cable itself. Some cables have connectors with locking 

tabs; if you are disconnecting this type of cable, press in on the locking tabs before you disconnect the cable. As you pull connectors apart, keep 
them evenly aligned to avoid bending any connector pins. Also, before you connect a cable, ensure that both connectors are correctly oriented 
and aligned.

 

CAUTION: 

To avoid damaging the computer, perform the following steps before you begin working inside the computer.

 

CAUTION: 

To disconnect a network cable, first unplug the cable from your computer and then unplug the cable from the network device. 

 

CAUTION: 

Before touching anything inside your computer, ground yourself by touching an unpainted metal surface, such as the metal at the back 

of the computer. While you work, periodically touch an unpainted metal surface to dissipate static electricity, which could harm internal 
components.

 

CAUTION: 

To avoid losing data, save and close all open files and exit all open programs before you turn off your computer.

Содержание OptiPlex 760












































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для OptiPlex 760

IBM Aptiva 2140 Maintenance Service Manual preview
Aptiva 2140
Бренд: IBM Страницы: 212
IBM 9228 - IntelliStation Z - Pro Installation Manual preview
9228 - IntelliStation Z - Pro
Бренд: IBM Страницы: 72
IBM 9114-275 - IntelliStation POWER 275 Installation Manual preview
9114-275 - IntelliStation POWER 275
Бренд: IBM Страницы: 102
IBM 8863 - eServer xSeries 366 Installation Manual preview
8863 - eServer xSeries 366
Бренд: IBM Страницы: 94
IBM 8543 Hints And Tips preview
8543
Бренд: IBM Страницы: 4
IBM 4190 User Manual preview
4190
Бренд: IBM Страницы: 84
IBM 2283 User Manual preview
2283
Бренд: IBM Страницы: 96
IBM 5280 User'S Setup Procedures preview
5280
Бренд: IBM Страницы: 156
IBM 5280 Technical Newsletter preview
5280
Бренд: IBM Страницы: 178
IBM 5280 Maintenance Information Manual preview
5280
Бренд: IBM Страницы: 155
IBM Aptiva 2159 Hardware Maintenance Service preview
Aptiva 2159
Бренд: IBM Страницы: 214
Igel UD2 Series Specifications preview
UD2 Series
Бренд: Igel Страницы: 2
iDOT BX2 User Handbook Manual preview
BX2
Бренд: iDOT Страницы: 66
Festo MPS PA Compact Manual preview
MPS PA Compact
Бренд: Festo Страницы: 72
Advantech ARK-3531 Series User Manual preview
ARK-3531 Series
Бренд: Advantech Страницы: 84
Advantech EPC-C301 Series User Manual preview
EPC-C301 Series
Бренд: Advantech Страницы: 80
StarTech.com ARMSTS Instruction Manual preview
ARMSTS
Бренд: StarTech.com Страницы: 29
Sony VAIO Digital Studio computer Service Manual preview
VAIO Digital Studio computer
Бренд: Sony Страницы: 23

Бренды по названию

Популярные бренды

Загрузить еще бренды