Dell OptiPlex 760 Скачать руководство пользователя страница 117

Страница: 117 / 203

Set the processor lightly in the socket and ensure that the processor is positioned correctly.

When the processor is fully seated in the socket, close the processor cover.

Ensure that the tab on the processor cover is positioned underneath the center cover latch on the socket.

Pivot the socket release lever back toward the socket and snap it into place to secure the processor.

10.

Clean the thermal grease from the bottom of the heat sink.

11.

Apply the new thermal grease to the top of the processor.

12.

Install the heat sink assembly:

Place the heat sink assembly back onto the heat-sink assembly bracket.

Rotate the heat sink assembly down towards the computer base and tighten the two captive screws.

1 processor cover

2 tab

3 processor

4 processor socket

5 center cover latch

6 release lever

7 front alignment-notch 8 socket and processor pin-1 indicator

9 rear alignment-notch

CAUTION:

To avoid damage, ensure that the processor aligns properly with the socket, and do not use excessive force when you install the

processor.

CAUTION:

Ensure that you apply new thermal grease. New thermal grease is critical for ensuring adequate thermal bonding, which is a

requirement for optimal processor operation.

CAUTION:

Ensure that the heat sink is correctly seated and secure.

Содержание OptiPlex 760












































































































































































































Результаты поиска

Содержание OptiPlex 760

Отзывы:

Похожие инструкции для OptiPlex 760

Бренды по названию

Популярные бренды

Dell OptiPlex 760, Руководство по обслуживанию

Результаты поиска

Содержание OptiPlex 760

Отзывы:

Похожие инструкции для OptiPlex 760

Бренды по названию

Популярные бренды