manualshive.com logo in svg

Dell OptiPlex 760, Руководство по обслуживанию

Характеристики Dell OptiPlex 760 доступны для скачивания бесплатно на manualshive.com. Здесь вы сможете получить подробное руководство пользователя с описанием всех функций и характеристик этого продукта. Узнайте больше о вашем устройстве, загрузив руководство на manualshive.com.

Поделиться
Скачать
background image

  

 

 

8.

Pull the drive release latch and slide the media card reader towards the back of the computer. Then lift up to remove the media card reader from the 
computer.  
 

 

  

9.

Replace the hard drive (see 

Installing a Hard Drive

).  

 

 

  

10.

Replace the computer cover (see 

Replacing the Computer Cover

).  

 

 

 

Installing a Media Card Reader  

  

 

 

1.

If you are replacing a media card reader, remove the installed media card reader (see 

Removing a Media Card Reader

), and skip to 

step 3

.  

 

 

  

2.

If you are installing a new media card reader, perform the following steps before continuing to 

step 3

:  

 

a.

 

Follow the procedures in 

Working on Your Computer

.  

 

b.

 

Remove the computer cover (see 

Removing the Computer Cover

).  

 

c.

 

Lay the computer on its side so that the system board is on the bottom of the inside of the computer.  

 

d.

 

Remove the drive panel insert.  

 

 

  

3.

Align the screws on the media card reader with the bracket slots in the computer, and gently position the drive until it clicks into place.  
 

 

  

4.

Connect the cable into the connectors on the media card reader and INT_USB connector on the system board.  
 

1  media card reader cable 

2  INT_USB connector on the system board 

1 

media card reader 

2 

screws (3) 

Содержание OptiPlex 760












































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для OptiPlex 760

AXIOMTEK eBOX530-820-FL Series Quick Installation Manual preview
eBOX530-820-FL Series
Бренд: AXIOMTEK Страницы: 2
M5Stack POECAM Manual preview
POECAM
Бренд: M5Stack Страницы: 15
Amplicon Impact 1015 User Manual preview
Impact 1015
Бренд: Amplicon Страницы: 92
MiTAC Master MP1-11TGS Series Getting Started With preview
Master MP1-11TGS Series
Бренд: MiTAC Страницы: 2
Vivo CART-V06A Instruction Manual preview
CART-V06A
Бренд: Vivo Страницы: 12
IBM 3196 Setup Instructions preview
3196
Бренд: IBM Страницы: 52
Shuttle XH410G Quick Manual preview
XH410G
Бренд: Shuttle Страницы: 3
Shuttle P22U User Manual preview
P22U
Бренд: Shuttle Страницы: 25
Thermaltake Soprano VO9000 Series User Manual preview
Soprano VO9000 Series
Бренд: Thermaltake Страницы: 16
Thermaltake H350 TG User Manual preview
H350 TG
Бренд: Thermaltake Страницы: 12
Thermaltake ARMOR REVO User Manual preview
ARMOR REVO
Бренд: Thermaltake Страницы: 18
Fellowes Lotus LT Instructions Manual preview
Lotus LT
Бренд: Fellowes Страницы: 11
ROBINHOOD ST9000W Installation And Operating Instrictions preview
ST9000W
Бренд: ROBINHOOD Страницы: 10
FabiaTech FX5632 Series Users Quick Reference preview
FX5632 Series
Бренд: FabiaTech Страницы: 3
FabiaTech FX5626 Users Quick Reference preview
FX5626
Бренд: FabiaTech Страницы: 4
Gotharman Gotharman's Little deFormer Manual preview
Gotharman's Little deFormer
Бренд: Gotharman Страницы: 30
Embedded Computer EPC-5500 Pentium M Operation Manual preview
EPC-5500 Pentium M
Бренд: Embedded Computer Страницы: 92
Ergotron WorkFit-PD Assembly Instructions Manual preview
WorkFit-PD
Бренд: Ergotron Страницы: 6

Бренды по названию

Популярные бренды

Загрузить еще бренды