Dell OptiPlex 760 Скачать руководство пользователя страница 91

Страница: 91 / 203

Attach the cable to the media card reader and to the system board.

Replace the computer cover (see

Replacing the Computer Cover

Verify that your computer works correctly by running the Dell Diagnostics (see

Dell Diagnostics

Optical Drive

Removing an Optical Drive

Follow the procedures in

Working on Your Computer

Remove the computer cover (see

Removing the Computer Cover

Disconnect the power and data cables from the back of the drive and system board.

media card reader

shoulder screws (4)

shoulder screw slots (2)

data/power cable

media card reader

WARNING:

Before working inside your computer, read the safety information that shipped with your computer. For additional safety best

practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.

WARNING:

To guard against electrical shock, always unplug your computer from the electrical outlet before replacing the cover.

Содержание OptiPlex 760












































































































































































































Результаты поиска

Содержание OptiPlex 760

Отзывы:

Похожие инструкции для OptiPlex 760

Бренды по названию

Популярные бренды

Dell OptiPlex 760, Руководство по обслуживанию

Результаты поиска

Содержание OptiPlex 760

Отзывы:

Похожие инструкции для OptiPlex 760

Бренды по названию

Популярные бренды