Dell OptiPlex 760 Скачать руководство пользователя страница 129

Страница: 129 / 203

Pull the cable release tab to disconnect the data cable from the system board.

Pull the drive release latch and slide the floppy drive towards the back of the computer. Then lift up to remove the drive.

Gently lift the data cable from the floppy data cable edge connector.

Replace the computer cover (see

Replacing the Computer Cover

Installing a Floppy Drive

If you are:

Installing a new floppy drive, remove the drive panel insert.

Replacing a drive, remove the floppy drive (see

Removing a Floppy Drive

Align the screws on the drive with the bracket slots in the computer and gently position the drive until it clicks into place.

Insert the data cable into the cable release tab on the floppy drive and press down on the tab until it clicks to lock it in place.

Insert the data cable into the connector on the system board.

CAUTION:

Do not pull the drive out of the computer by the drive cables. Doing so may cause damage to cables and the cable connectors.

cable release tab

data cable edge connector

floppy drive

screws (3)

bracket slots (3)

Содержание OptiPlex 760












































































































































































































Результаты поиска

Содержание OptiPlex 760

Отзывы:

Похожие инструкции для OptiPlex 760

Бренды по названию

Популярные бренды

Dell OptiPlex 760, Руководство по обслуживанию

Результаты поиска

Содержание OptiPlex 760

Отзывы:

Похожие инструкции для OptiPlex 760

Бренды по названию

Популярные бренды