Dell OptiPlex 760 Скачать руководство пользователя страница 181

Страница: 181 / 203

Removing and Installing a Device When Your Computer Is Running

Microsoft

Windows

To remove a device installed in the module bay, double-click the

Safely Remove Hardware

icon on the taskbar.

In the list of devices that appears on your screen, click the device you want to eject.

When a computer message indicates that you can remove the device, remove the device from the module bay.

Slide the new device into the module bay.

Securing a Device in the Module Bay

Remove the computer cover (see

Removing the Computer Cover

Gently press the module locking switch down until it locks into place.

1 bottom of computer 2 security screw

NOTE:

Installing and removing a device while the computer is running may not be applicable to all SATA operating modes. To enable this feature, set

SATA Operation

AHCI

RAID Operation

in the system setup program.

NOTE:

You cannot remove a device if your computer is turned on and the device is locked in the module bay. You must shut down the computer

and follow the steps in

Removing and Installing a Device When Your Computer Is Turned Off

to remove a locked device.

CAUTION:

Do not place any heavy objects on top of the computer. Doing so may bend the chassis and cause difficulty in removing a module

device.

Содержание OptiPlex 760












































































































































































































Результаты поиска

Содержание OptiPlex 760

Отзывы:

Похожие инструкции для OptiPlex 760

Бренды по названию

Популярные бренды

Dell OptiPlex 760, Руководство по обслуживанию

Результаты поиска

Содержание OptiPlex 760

Отзывы:

Похожие инструкции для OptiPlex 760

Бренды по названию

Популярные бренды