Dell OptiPlex 760 Скачать руководство пользователя страница 195

Страница: 195 / 203

Back to Contents Page

Dell™ OptiPlex™ 760 Service Manual

System Fans

System Fans

Removing the System Fans

Follow the procedures in

Working on Your Computer

Remove the cover of your computer (see

Removing the Computer Cover

Remove the fan shroud by lifting the fan shroud up and away from the computer.

Facing the back of the computer, remove the four screws that secure the system-board sled to the computer chassis.

Slide the system-board sled towards the back of the computer and lift it up and away from the computer chassis.

Disconnect the fan cables from the system board.

To remove the front fan, press the fan release tab and slide the fan away from the memory modules.

To remove the back fan, press the fan release tab and slide the fan away from the drives.

Installing the System Fans

To replace the fan, follow the removal procedures in the reverse order.

Replace the computer cover (see

Replacing the Computer Cover

Turn on the computer.

WARNING:

Before working inside your computer, read the safety information that shipped with your computer. For additional safety best

practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.

CAUTION:

To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of

your computer's electronic components. You can do so by touching an unpainted metal surface on the computer chassis.

back fan release tab

back fan power cable

front fan release tab

front fan power cable

Содержание OptiPlex 760












































































































































































































Результаты поиска

Содержание OptiPlex 760

Отзывы:

Похожие инструкции для OptiPlex 760

Бренды по названию

Популярные бренды

Dell OptiPlex 760, Руководство по обслуживанию

Результаты поиска

Содержание OptiPlex 760

Отзывы:

Похожие инструкции для OptiPlex 760

Бренды по названию

Популярные бренды