Dell OptiPlex 760 Скачать руководство пользователя страница 192

Страница: 192 / 203

Remove the computer cover (see

Removing the Computer Cover

If you are installing a new drive, rather than replacing an already installed drive:

Check the documentation for the drive to verify that the drive is configured for your computer.

Attach the plastic drive rails

—

located inside the cover

—

to the new drive and skip to

step 6

Remove the installed hard drive (see

Removing the Hard Drive

Remove the four screws that secure the drive rails to the existing hard drive, and attach the drive rails to the replacement hard drive.

Slide the hard drive into the hard drive bracket.

Attach the data and power cables to the hard drive connectors, ensuring that the connectors are properly oriented before connecting them.

Replace the computer cover (see

Replacing the Computer Cover

Replace the cable cover, if used.

10.

See the documentation that came with the drive for instructions on installing any software required for drive operation.

11.

Reboot the computer.

12.

Partition and logically format your drive before you proceed to the next step.

1 drive

2 drive rails (2)

3 screws (4)

CAUTION:

If you are replacing a hard drive that contains data you want to keep, back up your files before you begin this procedure.

CAUTION:

Serial ATA data and power connectors are keyed for correct insertion; that is, a notch or a missing pin on one connector matches a tab

or a filled-in hole on the other connector. When connecting cables to a drive, ensure that the connectors are oriented properly before you attach
the cables to the drive.

Содержание OptiPlex 760












































































































































































































Результаты поиска

Содержание OptiPlex 760

Отзывы:

Похожие инструкции для OptiPlex 760

Бренды по названию

Популярные бренды

Dell OptiPlex 760, Руководство по обслуживанию

Результаты поиска

Содержание OptiPlex 760

Отзывы:

Похожие инструкции для OptiPlex 760

Бренды по названию

Популярные бренды