Dell OptiPlex 760 Скачать руководство пользователя страница 68

Страница: 68 / 203

Replace the computer cover (see

Replacing the Computer Cover

Connect your computer and devices to electrical outlets, and turn them on.

When the message appears stating that memory size has changed, press <F1> to continue.

Log on to your computer.

10.

Right-click the

My Computer

icon on your Windows desktop and click

Properties

11.

Click the

General

tab.

12.

To verify that the memory is installed correctly, check the amount of memory (RAM) listed.

Removing Memory Module (s)

Follow the procedures in

Working on Your Computer

Remove the computer cover (see "Removing the Computer Cover" for your specific computer).

Press out the securing clip at each end of the memory module connector.

Grasp the module and pull up.

If the module is difficult to remove, gently ease the module back and forth to remove it from the connector.

Back to Contents Page

CAUTION:

To connect a network cable, first plug the cable into the network port or device and then plug it into the computer.

WARNING:

Before working inside your computer, read the safety information that shipped with your computer. For additional safety best

practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.

CAUTION:

To avoid electrostatic discharge and damage to internal components, ground yourself by using a wrist grounding strap or by

periodically touching an unpainted metal surface on the computer chassis.

Содержание OptiPlex 760












































































































































































































Результаты поиска

Содержание OptiPlex 760

Отзывы:

Похожие инструкции для OptiPlex 760

Бренды по названию

Популярные бренды

Dell OptiPlex 760, Руководство по обслуживанию

Результаты поиска

Содержание OptiPlex 760

Отзывы:

Похожие инструкции для OptiPlex 760

Бренды по названию

Популярные бренды