Dell OptiPlex 760 Скачать руководство пользователя страница 147

Страница: 147 / 203

Ultra Small Form Factor System Board Screws

Replacing the System Board

Gently align the board into the chassis and slide it toward the back of the computer.

Replace the screws on the system board.

Replace any components and cables that you removed from the system board.

Reconnect all cables to their connectors at the back of the computer.

Replace the computer cover (see

Replacing the Computer Cover

1 screws (9)

1 screws (10)

NOTE:

The system board is shipped in manufacturing mode. The user or service provider must select the manageability option upon first boot. See

Manageability

on how to select the manageability mode.

Содержание OptiPlex 760












































































































































































































Результаты поиска

Содержание OptiPlex 760

Отзывы:

Похожие инструкции для OptiPlex 760

Бренды по названию

Популярные бренды

Dell OptiPlex 760, Руководство по обслуживанию

Результаты поиска

Содержание OptiPlex 760

Отзывы:

Похожие инструкции для OptiPlex 760

Бренды по названию

Популярные бренды