Dell OptiPlex 760 Скачать руководство пользователя страница 130

Страница: 130 / 203

Replace the optical drive (see

Optical Drive

Check all cable connections, and fold cables out of the way to provide airflow for the fan and cooling vents.

Replace the computer cover (see

Replacing the Computer Cover

Enter system setup and use the

Diskette Drive

option to enable your new floppy drive (see

System Setup

See the documentation that came with the drive for instructions on installing any software required for drive operation.

Verify that your computer works correctly by running the Dell Diagnostics (see

Dell Diagnostics

Media Card Reader

Removing a Media Card Reader

Follow the procedures in

Working on Your Computer

Lay the computer on its side so that the system board is on the bottom of the inside of the computer.

Remove the computer cover (see

Removing the Computer Cover

Remove the optical drive and carefully set it aside (see

Optical Drive

Remove the cable from the media card reader connector.

Remove the hard drive (see

Removing a Hard Drive

Disconnect the media card reader cable from the system board.

cable release tab

floppy drive data cable edge connector

WARNING:

Before working inside your computer, read the safety information that shipped with your computer. For additional safety best

practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.

WARNING:

To guard against electrical shock, always unplug your computer from the electrical outlet before removing the computer cover.

CAUTION:

Do not pull the drive out of the computer by the drive cables. Doing so may cause damage to cables and the cable connectors.

Содержание OptiPlex 760












































































































































































































Результаты поиска

Содержание OptiPlex 760

Отзывы:

Похожие инструкции для OptiPlex 760

Бренды по названию

Популярные бренды

Dell OptiPlex 760, Руководство по обслуживанию

Результаты поиска

Содержание OptiPlex 760

Отзывы:

Похожие инструкции для OptiPlex 760

Бренды по названию

Популярные бренды