manualshive.com logo in svg

Dell OptiPlex 760, Руководство по обслуживанию

Характеристики Dell OptiPlex 760 доступны для скачивания бесплатно на manualshive.com. Здесь вы сможете получить подробное руководство пользователя с описанием всех функций и характеристик этого продукта. Узнайте больше о вашем устройстве, загрузив руководство на manualshive.com.

Поделиться
Скачать
background image

Back to Contents Page

  

 

 Mini Tower  

Dell™ OptiPlex™ 760 Service Manual 

 

  

Removing the Computer Cover 

 

  

Inside Your Computer 

 

  

System Board Components 

 

 

 

Removing the Computer Cover  

 

 

 

 

 

 

1.

Follow the procedures in 

Working on Your Computer

.  

 

 

  

2.

If you have installed a padlock through the padlock ring on the back panel, remove the padlock.  
 

 

  

3.

Locate the cover release latch shown in the illustration. Then, pull the cover release latch back as you lift the cover.  
 

 

  

4.

Grip the sides of the computer cover and pivot the cover up using the hinge tabs as leverage points.  
 

 

  

5.

Remove the cover from the hinge tabs and set it aside on a soft nonabrasive surface.  
 

 

 

  

 

Inside Your Computer  

 

 

 

WARNING: 

Before working inside your computer, read the safety information that shipped with your computer. For additional safety best 

practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance. 

 

WARNING: 

To guard against electrical shock, always unplug your computer from the electrical outlet before removing the computer cover. 

 

WARNING: 

Graphics card heat sinks can become very hot during normal operation. Ensure that the graphics card heat sink has had sufficient time 

to cool before you touch it. 

1 

security cable slot 

2 

cover release latch 

3 

padlock ring 

 

 

 

 

Содержание OptiPlex 760












































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для OptiPlex 760

IBM NetVista Quick Reference Manual preview
NetVista
Бренд: IBM Страницы: 68
IBM NetVista A30 Handboek Voor De Gebruiker preview
NetVista A30
Бренд: IBM Страницы: 54
Energy Star Xi3 NUC Lear Instruction Manual preview
Xi3 NUC Lear
Бренд: Energy Star Страницы: 17
OEM Tools 24616 Operating Instructions And Parts Manual preview
24616
Бренд: OEM Tools Страницы: 4
Zotac ZBOX EDGE MI623 User Manual preview
ZBOX EDGE MI623
Бренд: Zotac Страницы: 21
Gateway E-1000 Series User Manual preview
E-1000 Series
Бренд: Gateway Страницы: 50
Siemens INOX PRO SIMATIC IPC277D Operating Instructions Manual preview
INOX PRO SIMATIC IPC277D
Бренд: Siemens Страницы: 182
Siemens SIMATIC IPC847C Getting Started preview
SIMATIC IPC847C
Бренд: Siemens Страницы: 46
Siemens SIMATIC PC RI25 Manual preview
SIMATIC PC RI25
Бренд: Siemens Страницы: 64
Siemens SIMATIC Panel PC 677 Operating Instructions Manual preview
SIMATIC Panel PC 677
Бренд: Siemens Страницы: 94
Siemens SIMATIC PG 760 PII Manual preview
SIMATIC PG 760 PII
Бренд: Siemens Страницы: 120
Siemens simatic PC 577 Operating Instructions Manual preview
simatic PC 577
Бренд: Siemens Страницы: 192
Siemens SIMATIC IPC847D Operating Instructions Manual preview
SIMATIC IPC847D
Бренд: Siemens Страницы: 222
Sony PCV-W20 Marketing s Specifications preview
PCV-W20 Marketing s
Бренд: Sony Страницы: 1
Sony PCV-V300G VAIO User Guide (primary manual) Specifications preview
PCV-V300G VAIO User Guide (primary manual)
Бренд: Sony Страницы: 1
Sony PCV-W30 VAIO User Guide (primary manual) Manual preview
PCV-W30 VAIO User Guide (primary manual)
Бренд: Sony Страницы: 74
Sony PCV-W20 - VAIO - 512 MB RAM Online Help Manual preview
PCV-W20 - VAIO - 512 MB RAM
Бренд: Sony Страницы: 103
Sony PCV-V300G VAIO User Guide (primary manual) User Manual preview
PCV-V300G VAIO User Guide (primary manual)
Бренд: Sony Страницы: 209

Бренды по названию

Популярные бренды

Загрузить еще бренды