manualshive.com logo in svg

Dell OptiPlex 760, Руководство по обслуживанию, Страница: 201 / 203

Поделиться
Скачать
Dell OptiPlex 760 Скачать руководство пользователя страница 201

 

 

 

 

  

 

System Board Components  

  

 

WARNING: 

Before working inside your computer, read the safety information that shipped with your computer. For additional safety best 

practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance. 

 

WARNING: 

To avoid electrical shock, always unplug your computer from the AC power adapter before removing the cover. 

 

CAUTION: 

To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of 

your computer's electronic components. You can do so by touching an unpainted metal surface on the computer chassis.

1  fan shroud/heat sink assembly  2  speaker (optional) 

3  memory modules (2) 

4  hard drive 

5  security cable slot 

6  chassis intrusion switch 

1 

fan connector (FAN_FRONT) 

2 

internal speaker connector (INT_SPKR) 

3 

system board speaker (BEEP) 

4 

channel B memory connector (DIMM_2) 

5 

channel A memory connector (DIMM_1)  

6 

SATA data cable connector (SATA0) 

7 

battery (BATT) 

8 

password jumper (PSWD) 

9 

clear CMOS jumper (RTCRST) 

10  hard drive fan connector (FAN_HDD) 

11  hard drive power connector (SATA_PWR)  12  fan connector (FAN_REAR) 

13  intrusion switch connector (INTRUDER) 

14 

  power light (AUX_Power_LED) 

15  processor (CPU) 

 

 

 

 

Содержание OptiPlex 760












































































































































































































Отзывы:

Нет отзывов