manualshive.com logo in svg

Dell OptiPlex 760, Руководство по обслуживанию

Характеристики Dell OptiPlex 760 доступны для скачивания бесплатно на manualshive.com. Здесь вы сможете получить подробное руководство пользователя с описанием всех функций и характеристик этого продукта. Узнайте больше о вашем устройстве, загрузив руководство на manualshive.com.

Поделиться
Скачать
background image

Removing the Floppy Drive  

 

 

1.

Boot your computer and enter system setup (see 

Entering System Setup

). Use the 

Diskette Drive 

option to disable the floppy drive.  

 

 

  

2.

Follow the procedures in 

Working on Your Computer

.  

 

 

  

3.

Remove the computer cover (see 

Removing the Computer Cover

).  

 

 

  

4.

Remove the drive panel by sliding the drive release latch downward to open the panel, and then remove it from the hinges.  
 

 

  

5.

Disconnect the power and data cables from the back of the floppy drive and the system board.  
 

  

 

 

6.

Grasp the sliding plate lever and slide it towards the bottom of the computer until the drive panel snaps open; while holding the lever in place, slide the 
drive out of the computer.  
 

 

 

Installing the Floppy Drive  

 

 

1.

If you are replacing a floppy drive, remove the shoulder screws from the existing drive and attach the screws to the replacement drive.  
 

 

  

2.

If you are installing a new floppy drive, remove the drive-panel insert for the 3.5-inch drive bay, remove the shoulder screws from the inside of the drive-
panel insert and attach the screws to the new drive.  
 

  

 

 

3.

Align the shoulder screws on the floppy drive with the shoulder screw slots, and gently slide it into the bay until it clicks into place.  
 

1 

floppy drive 

2 

drive release latch 

Содержание OptiPlex 760












































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для OptiPlex 760

IBM PC 300PL Types 6862 Installation Manual preview
PC 300PL Types 6862
Бренд: IBM Страницы: 112
Aaeon TKS-G50-QM77 Manual preview
TKS-G50-QM77
Бренд: Aaeon Страницы: 117
Digital Equipment DEC 3000 Model 400S AXP Upgrade Instructions preview
DEC 3000 Model 400S AXP
Бренд: Digital Equipment Страницы: 13
Chipsee AI0-CM4-101 User Manual preview
AI0-CM4-101
Бренд: Chipsee Страницы: 21
Seametrics FT420 Instructions preview
FT420
Бренд: Seametrics Страницы: 4
Rockwell Automation Allen-Bradley VersaView 6180W-12BPXPH User Manual preview
Allen-Bradley VersaView 6180W-12BPXPH
Бренд: Rockwell Automation Страницы: 70
Ergotron TeachWell Mobile Digital WorkSpace Assembly Instructions Manual preview
TeachWell Mobile Digital WorkSpace
Бренд: Ergotron Страницы: 6
Rise RS-4702 User Manual preview
RS-4702
Бренд: Rise Страницы: 31
Radio Shack TRS-8O Operator'S Manual preview
TRS-8O
Бренд: Radio Shack Страницы: 58
IBM NetVista 6644 User Manual preview
NetVista 6644
Бренд: IBM Страницы: 110
IBM NetVista 6644 Quick Reference Manual preview
NetVista 6644
Бренд: IBM Страницы: 45
Tangent Medix T22B Replacement Instructions Manual preview
Medix T22B
Бренд: Tangent Страницы: 8
Baker Bugbox Plus UM-017 User Manual preview
Bugbox Plus UM-017
Бренд: Baker Страницы: 47
Lanner LEC-6040 User Manual preview
LEC-6040
Бренд: Lanner Страницы: 27
IBM NetVista X40 Wprowadzenie Manual preview
NetVista X40
Бренд: IBM Страницы: 54
Neousys POC-100 Series User Manual preview
POC-100 Series
Бренд: Neousys Страницы: 65
HANNspree SN22A1 series User Manual preview
SN22A1 series
Бренд: HANNspree Страницы: 57
IBM 7012 G Series Service Manual preview
7012 G Series
Бренд: IBM Страницы: 264

Бренды по названию

Популярные бренды

Загрузить еще бренды