Dell OptiPlex 760 Скачать руководство пользователя страница 113

Страница: 113 / 203

11.

Replace the computer cover (see

Replacing the Computer Cover

12.

Uninstall the card's driver. See the documentation that came with the card for instructions.

13.

If you removed a sound card:

Enter system setup, select

System Configuration

Miscellaneous Devices

, and change the

Audio

setting to

Enabled.

(See

Entering System

Setup

Connect external audio devices to the sound card's connectors. Do not connect external audio devices to the microphone, speaker/headphone,

or line-in connectors on the back panel of the computer.

14.

If you removed a network adapter card and want to turn on the integrated network adapter:

Enter system setup, select

System Configuration

Integrated NIC

, and change the setting to

Enabled

. (See

Entering System Setup

Connect the network cable to the integrated the back panel of the computer.

PS/2 Serial Port Adapter

Installing a PS/2 Serial Port Adapter

Follow the procedures in

Working on Your Computer

Remove the computer cover (see

Removing the Computer Cover

Gently lift the release tab on the card retention latch from the inside and pivot the latch open.

Remove the filler bracket (if applicable).

Align the PS/2 serial-port adapter bracket in the retention slot and press down firmly. Ensure that the adapter is fully seated in the slot.

Before you close the card retention mechanism, ensure that:

The tops of all cards and filler brackets are flush with the alignment bar.

The notch in the top of the card or filler bracket fits around the alignment guide.

Secure the card(s) by closing the card retention latch and snapping it into place.

NOTE:

See the documentation that came with the adapter for information on configuring the adapter, making internal connections, or customizing it for

your computer.

CAUTION:

Do not route card cables over the cards. Cables routed over the cards can prevent the computer cover from closing properly or cause

damage to the equipment.

1 release tab

2 adapter retention latch

3 serial port adapter bracket

4 serial port adapter

connector

5 serial port adapter system board connector

(PS2/SERIAL2)

Содержание OptiPlex 760












































































































































































































Результаты поиска

Содержание OptiPlex 760

Отзывы:

Похожие инструкции для OptiPlex 760

Бренды по названию

Популярные бренды

Dell OptiPlex 760, Руководство по обслуживанию

Результаты поиска

Содержание OptiPlex 760

Отзывы:

Похожие инструкции для OptiPlex 760

Бренды по названию

Популярные бренды