Dell OptiPlex 760 Скачать руководство пользователя страница 173

Страница: 173 / 203

A program crashes repeatedly

Check the software documentation

—

If necessary, uninstall and then reinstall the program.

A program is designed for an earlier Windows operating system

Run the Program Compatibility Wizard

—

Windows XP

The Program Compatibility Wizard configures a program so that it runs in an environment similar to non-XP operating system environments.

Click

Start

All Programs

Accessories

Program Compatibility Wizard

Next

Follow the instructions on the screen.

Windows Vista

The Program Compatibility Wizard configures a program so that it runs in an environment similar to non-Windows Vista operating system environments.

Click

Start

Control Panel

Programs

Use an older program with this version of Windows.

In the welcome screen, click

Next

Follow the instructions on the screen.

A solid blue screen appears

Turn the computer off

—

If you are unable to get a response by pressing a key on your keyboard or moving your mouse, press and hold the power button for

at least 8 to 10 seconds (until the computer turns off), and then restart your computer.

Other software problems

Check the software documentation or contact the software manufacturer for troubleshooting information

—

Ensure that the program is compatible with the operating system installed on your computer.

Ensure that your computer meets the minimum hardware requirements needed to run the software. See the software documentation for information.

Ensure that the program is installed and configured properly.

Verify that the device drivers do not conflict with the program.

If necessary, uninstall and then reinstall the program.

Back up your files immediately

Use a virus-scanning program to check the hard drive, floppy disks, CDs, or DVDs

Save and close any open files or programs and shut down your computer through the Start menu

Memory Problems

If you receive an insufficient memory message

—

Save and close any open files and exit any open programs you are not using to see if that resolves the problem.

See the software documentation for minimum memory requirements. If necessary, install additional memory (see

Installing Memory Module (s)

Reseat the memory modules (see

Memory

) to ensure that your computer is successfully communicating with the memory.

Run the Dell Diagnostics (see

Dell Diagnostics

If you experience other memory problems

—

NOTE:

Most software includes installation instructions in its documentation or on a floppy disk, CD, or DVD.

WARNING:

Before working inside your computer, read the safety information that shipped with your computer. For additional safety best

practices information, see the Regulatory Compliance Homepage on www.dell.com at www.dell.com/regulatory_compliance.

Содержание OptiPlex 760












































































































































































































Результаты поиска

Содержание OptiPlex 760

Отзывы:

Похожие инструкции для OptiPlex 760

Бренды по названию

Популярные бренды

Dell OptiPlex 760, Руководство по обслуживанию

Результаты поиска

Содержание OptiPlex 760

Отзывы:

Похожие инструкции для OptiPlex 760

Бренды по названию

Популярные бренды