Dell OptiPlex 760 Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 203

Dell OptiPlex 760 Скачать руководство пользователя страница 35

3.

Pull up on the drive-release latch and slide the drive towards the back of the computer. Then, lift up to remove the drive from the computer.

4.

Disconnect the power and data cables from the back of the drive.

5.

If you are not replacing the optical drive at this time, install the optical drive insert by lowering it into the drive bay until it clicks into place. Contact Dell if
you need a drive bay insert.

Installing an Optical Drive

1.

Unpack the drive and prepare it for installation.
Check the documentation that accompanied the drive to verify that the drive is configured for your computer.

2.

Follow the procedures in

Working on Your Computer

.

3.

If you are

installing a new drive

, remove the drive inserts and then remove the three shoulder screws (see

Removing Drive Inserts

).

If you are

replacing an existing drive

, follow procedures in

Removing an Optical Drive

and remove the three shoulder screws from the existing drive.

4.

Insert the three shoulder screws into the sides of the new drive and tighten them.

5.

Connect the power and data cables to the drive.

6.

Align the shoulder screws with the screw guides, and slide the drive into the bay until it clicks into place.

CAUTION:

Do not pull the drive out of the computer by the drive cables. Doing so may cause damage to cables and the cable connectors.

1 drive release latch 2 optical drive

«
...
33
34
35
36
37
...
»

Содержание OptiPlex 760












































































































































































































Отзывы:

Нет отзывов