Dell OptiPlex 760 Скачать руководство пользователя страница 87

Страница: 87 / 203

Locate an unused SATA connector on the system board and attach a data cable to this connector and to the second hard drive.

Replace the computer cover (see

Replacing the Computer Cover

10.

Enter system setup (see

System Setup

), and update the SATA port option under the Drives option list.

11.

Exit system setup, and reboot the computer.

12.

Partition and logically format your drive.

See the documentation for your operating system for instructions.

13.

Test the hard drive by running the Dell Diagnostics (see

Dell Diagnostics

14.

If the drive you just installed is the primary drive, install your operating system on the hard drive.

Floppy Drive

data cable

hard drive system board connector

power cable

WARNING:

Before working inside your computer, read the safety information that shipped with your computer. For additional safety best

practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.

WARNING:

To guard against electrical shock, always unplug your computer from the electrical outlet before removing the computer cover.

Содержание OptiPlex 760












































































































































































































Результаты поиска

Содержание OptiPlex 760

Отзывы:

Dell OptiPlex 760, Руководство по обслуживанию, Страница: 87 / 203

Результаты поиска

Содержание OptiPlex 760

Отзывы: