Dell OptiPlex 760 Скачать руководство пользователя страница 171

Страница: 171 / 203

Error Messages

If the error message is not listed, see the documentation for the operating system or the program that was running when the message appeared.

A filename cannot contain any of the following characters: \ / : * ? " < > |

—

Do not use these characters in filenames.

A required .DLL file was not found

—

The program that you are trying to open is missing an essential file. To remove and then reinstall the program:

Windows XP

Click

Start

Control Panel

Add or Remove Programs

Programs and Features

Select the program you want to remove.

Click

Uninstall

See the program documentation for installation instructions.

Windows Vista

Click

Start

Control Panel

Programs

Programs and Features

Select the program you want to remove.

Click

Uninstall

See the program documentation for installation instructions.

drive letter

:\ is not accessible. The device is not ready

—

The drive cannot read the disk. Insert a disk into the drive and try again.

Insert bootable media

—

Insert a bootable floppy disk, CD, or DVD.

Non-system disk error

—

Remove the floppy disk from the floppy drive and restart your computer.

Not enough memory or resources. Close some programs and try again

—

Close all windows and open the program that you want to use. In some cases,

you may have to restart your computer to restore computer resources. If so, run the program that you want to use first.

Operating system not found

—

Contact Dell (see

Contacting Dell

IEEE 1394 Device Problems

Ensure that the cable for the IEEE 1394 device is properly inserted into the device and into the connector on the computer

Ensure that the IEEE 1394 device is enabled in system setup

—

See

System Setup Options

Ensure that the IEEE 1394 device is recognized by Windows

—

Windows XP

Click

Start and click

Control Panel

Under

Pick a Category

, click

Performance and Maintenance

System

System Properties

Hardware

Device Manager

Windows Vista

Click

Start

Control Panel

Hardware and Sound

Click

Device Manager.

If your IEEE 1394 device is listed, Windows recognizes the device.

WARNING:

Before working inside your computer, read the safety information that shipped with your computer. For additional safety best

practices information, see the Regulatory Compliance Homepage on www.dell.com at www.dell.com/regulatory_compliance.

WARNING:

Before working inside your computer, read the safety information that shipped with your computer. For additional safety best

practices information, see the Regulatory Compliance Homepage on www.dell.com at www.dell.com/regulatory_compliance.

NOTE:

Your computer supports only IEEE 1394a standard.

Содержание OptiPlex 760












































































































































































































Результаты поиска

Содержание OptiPlex 760

Отзывы:

Похожие инструкции для OptiPlex 760

Бренды по названию

Популярные бренды

Dell OptiPlex 760, Руководство по обслуживанию

Результаты поиска

Содержание OptiPlex 760

Отзывы:

Похожие инструкции для OptiPlex 760

Бренды по названию

Популярные бренды