Dell OptiPlex 760 Скачать руководство пользователя страница 24

Страница: 24 / 203

Before you close the card retention mechanism, ensure that:

The tops of all cards and filler brackets are flush with the alignment bar.

The notch in the top of the card or filler bracket fits around the alignment guide.

Secure any remaining card(s) by closing the card retention latch and snapping it into place.

Replace the computer cover (see

Replacing the Computer Cover

Installing a PS/2 Serial Port Adapter in the Riser-Card Cage

Follow the procedures in

Working on Your Computer

Remove the computer cover (see

Removing the Computer Cover

Remove the riser-card cage:

Check any cables connected to cards through the back panel openings. Disconnect any cables that will not reach the riser-card cage once they

are removed from the computer.

Rotate the riser-card cage handle up and gently pull on the handle to lift the riser-card cage up and away from the computer.

Gently lift the release tab on the card retention latch from the inside to pivot the latch open. Pivot the latch until it snaps into the open position.

If you are installing a new PS/2 serial port adapter, remove the filler bracket to create an empty card-slot opening.

If you are replacing a PS/2 adapter that is already installed in the computer, remove the adapter.

If necessary, disconnect any cables connected to the adapter.

Align the PS/2 serial-port adapter bracket in the retention slot and press down firmly. Ensure that the adapter is fully seated in the slot.

Before you close the card retention mechanism, ensure that:

The tops of all cards and filler brackets are flush with the alignment bar.

The notch in the top of the card or filler bracket fits around the alignment guide.

10.

Secure the card(s) by closing the card retention latch and snapping it into place.

11.

Connect the adapter cable to the PS/2 serial port adapter connector (PS2/SERIAL2) on the system board (see

System Board Components

riser-card cage

handle

riser cards (2)

WARNING:

To guard against electrical shock, be sure to unplug your computer from its electrical outlet before installing any cards or adapters.

CAUTION:

Do not route card cables over the cards. Cables routed over the cards can prevent the computer cover from closing properly or cause

damage to the equipment.

Содержание OptiPlex 760












































































































































































































Результаты поиска

Содержание OptiPlex 760

Отзывы:

Похожие инструкции для OptiPlex 760

Бренды по названию

Популярные бренды

Dell OptiPlex 760, Руководство по обслуживанию

Результаты поиска

Содержание OptiPlex 760

Отзывы:

Похожие инструкции для OptiPlex 760

Бренды по названию

Популярные бренды