Dell OptiPlex 760 Скачать руководство пользователя страница 155

Страница: 155 / 203

Assigning a System Password

To exit without assigning a system password, press <Esc> at any time (before you press the

button in step 4).

Enter system setup (see

Entering System Setup

Select

System

Password

, and verify that

Password Status

is set to

Not Set

Type your new system password.

You can use up to 32 characters. To erase a character when entering your password, press <Backspace>. The password is case sensitive.

Certain key combinations are not valid. If you enter one of these invalid combinations, the speaker emits a beep.

As you press each character key (or the spacebar for a blank space), a placeholder appears.

Type your new password a second time to confirm and press

button.

The password setting changes to

Set

Typing Your System Password

When you start or restart your computer, the following prompt appears on the screen.

Password

Status

is set to

Locked

Type the password and press <Enter>.

If you have assigned an administrator password, the computer accepts your administrator password as an alternate system password.

If you type a wrong or incomplete system password, the following message appears on the screen:

** Incorrect password. **

If you again type an incorrect or incomplete system password, the same message appears on the screen. The third and subsequent times you type an
incorrect or incomplete system password, the computer displays the following message:

** Incorrect password. **

Number of unsuccessful password attempts: 3

System halted! Must power down.

Even after your computer is turned off and on, the previous message is displayed each time you type an incorrect or incomplete system password.

Deleting or Changing an Existing System Password

Enter system setup (see

Entering System Setup

Go to

Security

System Password

and press <Enter>.

When prompted, type the system password.

Press <Enter> twice to clear the existing system password. The setting changes to

Not Set

is displayed, the system password is deleted. If

Not Set

is not displayed, press <Alt><b> to restart the computer, and then repeat steps 3

and 4.

To assign a new password, follow the procedure in

Assigning a System Password

Exit system setup.

Administrator Password

Option Settings

NOTE:

You can use

Password Status

in conjunction with

System Password

and

Admin Password

to further protect your computer from unauthorized

changes.

Содержание OptiPlex 760












































































































































































































Результаты поиска

Содержание OptiPlex 760

Отзывы:

Похожие инструкции для OptiPlex 760

Бренды по названию

Популярные бренды

Dell OptiPlex 760, Руководство по обслуживанию

Результаты поиска

Содержание OptiPlex 760

Отзывы:

Похожие инструкции для OptiPlex 760

Бренды по названию

Популярные бренды