manualshive.com logo in svg

Dell OptiPlex 760, Руководство по обслуживанию

Характеристики Dell OptiPlex 760 доступны для скачивания бесплатно на manualshive.com. Здесь вы сможете получить подробное руководство пользователя с описанием всех функций и характеристик этого продукта. Узнайте больше о вашем устройстве, загрузив руководство на manualshive.com.

Поделиться
Скачать
background image

  

b.

 

Gently lift the heat sink from the processor.  

 

c.

 

Lay the heat sink down on its top, with the thermal grease facing upward.  

 

 

 

 

 

5.

Open the processor cover by sliding the release lever from under the center cover latch on the socket. Then pull the lever back to release the processor. 
 
 

  

 

 

 

 

 

 

6.

Gently remove the processor from the socket.  
 

 

  

7.

Leave the release lever extended in the release position so that the socket is ready for the new processor.  
 

 

 

Installing the Processor 

 

 

1.

Unpack the new processor, being careful not to touch the underside of the processor.  
 

 

  

2.

If the release lever on the socket is not fully extended, move it to that position.  
 

 

  

3.

Orient the front and rear alignment-notches on the processor with the front and rear alignment-notches on the socket.  
 

1  top of heat sink  2  heat sink 

3  retention base 

4  release tab 

 

CAUTION: 

Unless a new heat sink is required for the new processor, reuse the original heat sink assembly when you replace the processor. 

1  center cover latch  2  processor cover 

3  processor 

4  socket 

5  release lever 

 

 

 

 

 

CAUTION: 

Ground yourself by touching an unpainted metal surface on the back of the computer.

 

CAUTION: 

When replacing the processor, do not touch any of the pins inside the socket or allow any objects to fall on the pins in the socket.

Содержание OptiPlex 760












































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для OptiPlex 760

3M Dynapro ET 3200 Series Getting Started Manual preview
Dynapro ET 3200 Series
Бренд: 3M Страницы: 23
IBASE Technology AMI200-8 User Manual preview
AMI200-8
Бренд: IBASE Technology Страницы: 32
IBM IntelliStation Z Pro Specifications preview
IntelliStation Z Pro
Бренд: IBM Страницы: 2
Chipsee AI0-CM4-101 User Manual preview
AI0-CM4-101
Бренд: Chipsee Страницы: 21
Intel NUC7CJYH Manual preview
NUC7CJYH
Бренд: Intel Страницы: 2
Vivo DESK-V000Q Instruction Manual preview
DESK-V000Q
Бренд: Vivo Страницы: 3
Datatech Enterprises Apex 386SX/20 User Manual preview
Apex 386SX/20
Бренд: Datatech Enterprises Страницы: 130
Moxa Technologies DA-682C Series User Manual preview
DA-682C Series
Бренд: Moxa Technologies Страницы: 53
Shuttle XPC SA76 User Manual preview
XPC SA76
Бренд: Shuttle Страницы: 26
Vertical SBX IP Admin Manual preview
SBX IP
Бренд: Vertical Страницы: 338
PerfecTron ROC254A Quick Installation Manual preview
ROC254A
Бренд: PerfecTron Страницы: 7
Shuttle DS77U Series User Manual preview
DS77U Series
Бренд: Shuttle Страницы: 24
Veriton VN4660G Lifecycle Extension Manual preview
VN4660G
Бренд: Veriton Страницы: 41
iAN QII-11381 User Manual preview
QII-11381
Бренд: iAN Страницы: 16
HSS Hire MI TOWER Operating & Safety Manual preview
MI TOWER
Бренд: HSS Hire Страницы: 36
Jäger ADwin Manual For The Installation preview
ADwin
Бренд: Jäger Страницы: 69
Radio Shack 16B System Manual preview
16B
Бренд: Radio Shack Страницы: 90
Radio Shack TRS-80 Model 4 Introduction Manual preview
TRS-80 Model 4
Бренд: Radio Shack Страницы: 42

Бренды по названию

Популярные бренды

Загрузить еще бренды