manualshive.com logo in svg

Dell OptiPlex 760, Руководство по обслуживанию

Характеристики Dell OptiPlex 760 доступны для скачивания бесплатно на manualshive.com. Здесь вы сможете получить подробное руководство пользователя с описанием всех функций и характеристик этого продукта. Узнайте больше о вашем устройстве, загрузив руководство на manualshive.com.

Поделиться
Скачать
background image

Back to Contents Page

  

Dell™ OptiPlex™ 760 Service Manual 

 

  

Drives 

 

 

 

Drives  

Your computer supports: 

l

 

One serial ATA (SATA) hard drive 

 

l

 

One 3.5-inch drive bay (to support a floppy drive or a media card reader) 

 

l

 

One SATA optical drive 

 

  

 

 

General Drive Installation Guidelines 

SATA connectors on the system board are labeled SATA0 and SATA1. Hard drives must be connected to the lower-numbered SATA connectors. Any other SATA 
device (like an optical drive) must be connected to the remaining SATA connectors numbered higher than the one that the hard drive is connected to. For 
example, if you have a SATA hard drive and a SATA optical drive, connect the hard drive to the SATA0 connector and connect the SATA optical drive to the 
SATA1 connector (see 

System Board Components

 for the location of the SATA connectors on the system board). 

 

 

Connecting Drive Cables  

When you install a drive, you connect two cables

—

a DC power cable and a data interface cable

—

to the back of the drive.  

 

 

Data Interface Connectors  

 

NOTE: 

Due to the limited number of drive bays and controllers on this computer, you will not be able to connect all supported devices at once.

 

NOTE: 

If you will be operating your computer without an optical drive or a 3.5-inch device (floppy drive or media card reader) installed, the appropriate 

drive bay insert must be installed in place of the drive. Contact Dell if you need a drive bay insert.

1  optical drive  2  floppy drive 

3  hard drive 

 

 

 

 

 

 

SATA Connector

 

  

Содержание OptiPlex 760












































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для OptiPlex 760

IBM Aptiva Hardware Handbook preview
Aptiva
Бренд: IBM Страницы: 136
IBM Aptiva Handbook preview
Aptiva
Бренд: IBM Страницы: 202
IBM ThinkPad G40 Series Hardware Maintenance Manual preview
ThinkPad G40 Series
Бренд: IBM Страницы: 160
Icop D-3362-I Series User Manual preview
D-3362-I Series
Бренд: Icop Страницы: 14
Knoll Pixel Y-Leg Installation Instructions preview
Pixel Y-Leg
Бренд: Knoll Страницы: 2
Compaq d260 - Microtower Desktop PC Illustrated Parts Map preview
d260 - Microtower Desktop PC
Бренд: Compaq Страницы: 1
Acer Ferrari 1000 Series Service Manual preview
Ferrari 1000 Series
Бренд: Acer Страницы: 123
Acer Veriton 3000 User Manual preview
Veriton 3000
Бренд: Acer Страницы: 112
Jupiter H470 Quick Installation Manual preview
H470
Бренд: Jupiter Страницы: 2
Rasmus Althoff CT800 Manual preview
CT800
Бренд: Rasmus Althoff Страницы: 32
Toshiba Tecra S2 Specifications preview
Tecra S2
Бренд: Toshiba Страницы: 8
Toshiba TLCS-900 Family Data Book preview
TLCS-900 Family
Бренд: Toshiba Страницы: 751
Zotac ZBOX PRO QK5P1000 Quick Start Manual preview
ZBOX PRO QK5P1000
Бренд: Zotac Страницы: 57
Zotac ZBOX nano XS Quick Start Manual preview
ZBOX nano XS
Бренд: Zotac Страницы: 1
G-Wiz HCX-100G Manual preview
HCX-100G
Бренд: G-Wiz Страницы: 50
HNCSMILE C80 User Manual preview
C80
Бренд: HNCSMILE Страницы: 9
WeWi DBR1-Y Owner'S Manual preview
DBR1-Y
Бренд: WeWi Страницы: 29
Siemens Nixdorf PCD-B series Operating Manual preview
PCD-B series
Бренд: Siemens Nixdorf Страницы: 137

Бренды по названию

Популярные бренды

Загрузить еще бренды