Dell OptiPlex 760 Скачать руководство пользователя страница 73

Страница: 73 / 203

If necessary, disconnect any cables connected to the card.

If you are removing the card permanently, install a filler bracket in the empty card-slot opening.

Replace the computer cover (see

Replacing the Computer Cover

), reconnect the computer and devices to electrical outlets, and then turn them on.

Uninstall the card's driver. See the documentation that came with the card for instructions.

If you removed a sound card:

Enter system setup, select

System Configuration

Miscellaneous Devices

, and change the

Audio

setting to

Enabled

(see

Entering System

Setup

Connect external audio devices to the sound card's connectors. Do not connect external audio devices to the microphone, speaker/headphone,

or line-in connectors on the back panel of the computer.

If you removed a network adapter card and want to turn on the integrated network adapter:

Enter system setup, select

System Configuration

Integrated NIC

, and change the setting to

Enabled

(see

Entering System Setup

Connect the network cable to the integrated the back panel of the computer.

PS/2 Serial Port Adapter

Installing a PS/2 Serial Port Adapter

Follow the procedures in

Working on Your Computer

Remove the computer cover (see

Removing the Computer Cover

Gently push the release tab on the card retention latch from the inside to pivot the latch open. The latch will remain in the open position.

1 card retention latch 2 alignment guide

3 card

4 card-edge connector

5 card connector

6 release tab

NOTE:

Installing filler brackets over empty card-slot openings is necessary to maintain FCC certification of the computer. The brackets keep dust

and dirt out of your computer and maintains the airflow that cools your computer.

CAUTION:

To connect a network cable, first plug the cable into the network wall jack and then plug it into the computer.

WARNING:

Before working inside your computer, read the safety information that shipped with your computer. For additional safety best

practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.

CAUTION:

To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of

your computer's electronic components. You can do so by touching an unpainted metal surface on the computer chassis.

Содержание OptiPlex 760












































































































































































































Результаты поиска

Содержание OptiPlex 760

Отзывы:

Похожие инструкции для OptiPlex 760

Бренды по названию

Популярные бренды

Dell OptiPlex 760, Руководство по обслуживанию

Результаты поиска

Содержание OptiPlex 760

Отзывы:

Похожие инструкции для OptiPlex 760

Бренды по названию

Популярные бренды