Dell OptiPlex 760 Скачать руководство пользователя страница 72

Страница: 72 / 203

10.

Before you lower the card retention mechanism, ensure that:

The tops of all cards and filler brackets are flush with the alignment bar.

The notch in the top of the card or filler bracket fits around the alignment guide.

11.

Secure the card(s) by closing the card retention latch and snapping it into place.

12.

Connect any cables that should be attached to the card.

See the documentation for the card for information about the card's cable connections.

13.

Replace the computer cover (see

Replacing the Computer Cover

), reconnect the computer and devices to electrical outlets, and then turn them on.

14.

If you installed a sound card:

Enter system setup, select

System Configuration

Miscellaneous Devices

, and change the

Audio

setting to

Disabled

(see

Entering System

Setup

Connect external audio devices to the sound card's connectors. Do not connect external audio devices to the microphone, speaker/headphone,

or line-in connectors on the back panel of the computer.

15.

If you installed a network adapter card and want to turn off the integrated network adapter:

Enter system setup, select

System Configuration

Integrated NIC

, and change the setting to

Disabled

(see

Entering System Setup

Connect the network cable to the network adapter card's connectors. Do not connect the network cable to the integrated network connector on

the back panel of the computer.

16.

Install any drivers required for the card as described in the card documentation.

Removing a PCI or PCI Express Card

Follow the procedures in

Working on Your Computer

Remove the computer cover (see

Removing the Computer Cover

Gently push the release tab on the card retention latch from the inside to pivot the latch open. The latch will remain in the open position.

1 card fully seated

2 card not fully seated

3 bracket within slot 4 bracket caught outside of slot

CAUTION:

Do not route card cables over or behind the cards. Cables routed over the cards can prevent the computer cover from closing properly

or cause damage to the equipment.

CAUTION:

If you disable the integrated network adapter, you will not have Active Management Technology (AMT) functionality.

CAUTION:

To connect a network cable, first plug the cable into the network wall jack and then plug it into the computer.

Содержание OptiPlex 760












































































































































































































Результаты поиска

Содержание OptiPlex 760

Отзывы:

Похожие инструкции для OptiPlex 760

Бренды по названию

Популярные бренды

Dell OptiPlex 760, Руководство по обслуживанию

Результаты поиска

Содержание OptiPlex 760

Отзывы:

Похожие инструкции для OptiPlex 760

Бренды по названию

Популярные бренды