Dell OptiPlex 760 Скачать руководство пользователя страница 89

Страница: 89 / 203

Attach the power and data cables to the floppy drive and to the system board.

Replace the computer cover (see

Replacing the Computer Cover

Enter system setup (see

System Setup

), and use the

Diskette Drive

option to enable your new floppy drive.

Verify that your computer works correctly by running the Dell Diagnostics (see

Dell Diagnostics

Media Card Reader

Removing the Media Card Reader

Follow the procedures in

Working on Your Computer

Remove the computer cover (see

Removing the Computer Cover

floppy drive

shoulder screws (4)

shoulder screw slots (2)

power cable

data cable

floppy drive connector (DSKT)

WARNING:

Before working inside your computer, read the safety information that shipped with your computer. For additional safety best

practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.

WARNING:

To guard against electrical shock, always unplug your computer from the electrical outlet before removing the computer cover.

Содержание OptiPlex 760












































































































































































































Результаты поиска

Содержание OptiPlex 760

Отзывы:

Похожие инструкции для OptiPlex 760

Бренды по названию

Популярные бренды

Dell OptiPlex 760, Руководство по обслуживанию

Результаты поиска

Содержание OptiPlex 760

Отзывы:

Похожие инструкции для OptiPlex 760

Бренды по названию

Популярные бренды