Dell OptiPlex 760 Скачать руководство пользователя страница 74

Страница: 74 / 203

Remove the filler bracket (if applicable).

Align the PS/2 serial port adapter bracket in the retention slot and press down firmly. Ensure that the adapter is fully seated in the slot.

Before you close the card retention mechanism, ensure that:

The tops of all adapters and filler brackets are flush with the alignment bar.

The notch in the top of the adapter or filler bracket fits around the alignment guide.

Close the card retention latch and gently press until it snaps into place.

Connect the adapter cable to the serial port adapter connector (SERIAL2) on the system board (see

System Board Components

for connector locations).

card retention latch

alignment guide

NOTE:

See the documentation that came with the PS/2 serial port adapter for information on configuring the adapter, making internal connections,

or customizing it for your computer.

card fully seated

card not fully seated

bracket within slot

bracket caught outside of slot

CAUTION:

Do not route cables over any installed cards. Cables routed over the cards can prevent the computer cover from closing properly or

cause damage to the equipment.

Содержание OptiPlex 760












































































































































































































Результаты поиска

Содержание OptiPlex 760

Отзывы:

Похожие инструкции для OptiPlex 760

Бренды по названию

Популярные бренды

Dell OptiPlex 760, Руководство по обслуживанию

Результаты поиска

Содержание OptiPlex 760

Отзывы:

Похожие инструкции для OptiPlex 760

Бренды по названию

Популярные бренды