Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 293 | Manualshive

Страница: 293 / 444

background image

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 293

access

Syntax

access

Context

config>lag

Description

This command enables the context to configure access parameters.

adapt-qos

Syntax

adapt-qos

type

Context

config>lag>access

Description

This command specifies how the LAG SAP queue and virtual scheduler buffering and rate parameters
are adapted over multiple active MDAs. This command applies only to access LAGs.

Default

distribute

Parameters

type —

Specify the QoS adaptation type.

Values

link

— Specifies that the LAG will create the SAP queues and virtual schedulers

with the actual parameters on each MDA.

distribute

— Specifies that each MDA will receive a fraction of the SAP and

scheduler parameters.

dynamic-cost

Syntax

[

no

]

dynamic-cost

Context

config>lag

lag-id

Description

This command enables OSPF costing of a Link Aggregation Group (LAG) based on the available
aggregated, operational bandwidth.

The path cost is dynamically calculated based on the interface bandwidth. OSPF path cost can be
changed through the interface metric or the reference bandwidth.

If dynamic cost is configured, then costing is applied based on the total number of links configured
and the cost advertised is inversely proportional to the number of links available at the time. This is
provided that the number of links that are up exceeds the configured LAG threshold value at which
time the configured threshold action determines if, and at what cost, this LAG will be advertised.

For example:

Assume a physical link in OSPF has a cost associated with it of 100, and the LAG consists of
four physical links. The cost associated with the logical link is 25. If one link fails then the cost
would automatically be adjusted to 33.

If dynamic cost is not configured and OSPF autocost is configured, then costing is applied based on
the total number of links configured. This cost will remain static provided the number of links that are

«
...
291
292
293
294
295
...
»

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7750 SR OS

Бренд: Parker Страницы: 344

Бренд: Oracle Страницы: 112

Бренд: Jøtul Страницы: 20

JetNet 3508-LVDC

Бренд: Korenix Страницы: 16

FlexNetwork 5130 Series

Бренд: HPE Страницы: 33

Бренд: ZyXEL Communications Страницы: 2

Bolide BN-NVR/NX

Бренд: GSA Страницы: 101

Бренд: 8e6 Technologies Страницы: 94

DUAL Nx56/64 1200142L1#

Бренд: ADTRAN Страницы: 48

ipRocketLink 3101 Series

Бренд: Patton Страницы: 119

Бренд: WTI Страницы: 178

Бренд: ENKHO Страницы: 48

Бренд: Crestron Страницы: 2

Бренд: Crestron Страницы: 2

Бренд: Huawei Страницы: 23

Бренд: Huawei Страницы: 50

CX600-X1-M Series

Бренд: Huawei Страницы: 234

Бренд: Huawei Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды