manualshive.com logo in svg

Alcatel-Lucent 7750 SR OS, Руководство по настройке интерфейса, Страница: 312 / 444

Поделиться
Скачать
Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 312

Configuration Commands

Page 312

7750 SR OS Interface Configuration Guide

mcast-path-management

Syntax

mcast-path-management

Context

config>card>fp>ingress
config>card>mda>ingress

Description

This CLI node contains the forwarding plane or MDA settings for ingress multicast path 
management.  Enter the node to configure the bandwidth-policy, the individual path bandwidth 
overrides and the administrative state of ingress multicast path management.

bandwidth-policy

Syntax

bandwidth-policy 

policy-name

no bandwidth-policy

Context

config>card>fp>ingress>mcast-path-management
config>card>mda>ingress>mcast-path-management

Description

This command is used to explicitly associate a bandwidth policy to a forwarding plane or MDA. The 
bandwidth policy defines the dynamic rate table and the multicast paths bandwidth and queuing 
parameters.

If a bandwidth policy is not explicitly associated with a forwarding plane or MDA, the default 
bandwidth policy is used when ingress multicast path management is enabled.

The 

no

 form of the command removes an explicit bandwidth policy from a forwarding plane or MDA 

and restores the default bandwidth policy.

Parameters

policy-name — 

The policy-name parameter is required and defines the bandwidth policy that should 

be associated with the MDA or forwarding plane for ingress multicast path management. If the 
policy name does not exist, the bandwidth-policy command will fail.

Values

Any existing bandwidth policy name

Default

default

primary-override

Syntax

primary-override

Context

config>card>mda>ingress>mcast-mgmt

Description

This command enables the context to configure MDA ingress multicast path-limit overrides.

The path override CLI nodes are not supported on IOM-3.

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов