Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 187 | Manualshive

Страница: 187 / 444

background image

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 187

Card Commands

card

Syntax

card

slot-number

no card

slot-number

Context

config

Description

This mandatory command enables access to the chassis card Input/Output Module (IOM), slot, and
MDA CLI context.

The

no

form of this command removes the card from the configuration. All associated ports, services,

and MDAs must be shutdown.

Default

No cards are configured.

Parameters

slot-number —

The slot number of the card in the chassis.

Values

1 — 10 depending on chassis model.

SR-1:

slot-number

= 1

SR-7:

slot-number

= 1 — 5

SR-12:

slot-number

= 1 — 10

card-type

Syntax

card-type

card-type

no card-type

Context

config>card

Description

This mandatory command adds an IOM to the device configuration for the slot. The card type can be
preprovisioned, meaning that the card does not need to be installed in the chassis.

A card must be provisioned before an MDA, or port can be configured.

A card can only be provisioned in a slot that is vacant, meaning no other card can be provisioned
(configured) for that particular slot. To reconfigure a slot position, use the no form of this command
to remove the current information.

A card can only be provisioned in a slot if the card type is allowed in the slot. An error message is
generated if an attempt is made to provision a card type that is not allowed.

If a card is inserted that does not match the configured card type for the slot, then a medium severity
alarm is raised. The alarm is cleared when the correct card type is installed or the configuration is
modified.

A high severity alarm is raised if an administratively enabled card is removed from the chassis. The
alarm is cleared when the correct card type is installed or the configuration is modified. A low
severity trap is issued when a card is removed that is administratively disabled.

«
...
185
186
187
188
189
...
»

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7750 SR OS

Vb-C60 - Ptz Network Camera

Бренд: Canon Страницы: 30

8BIG RACK THUNDERBOLT 2

Бренд: LaCie Страницы: 28

Device Server UDS 10

Бренд: Lantronix Страницы: 8

Бренд: National Instruments Страницы: 36

Бренд: National Instruments Страницы: 34

QSR-3920 Series

Бренд: QTech Страницы: 120

Бренд: Fortinet Страницы: 20

Бренд: Toto Link Страницы: 55

Бренд: ICP DAS USA Страницы: 8

Enterasys Matrix 2G4082-25

Бренд: Enterasys Страницы: 58

Бренд: H3C Страницы: 4

Бренд: NBase Страницы: 18

Бренд: Gearlinx Страницы: 23

Бренд: Tripp Lite Страницы: 2

Бренд: JLCooper Electronics Страницы: 12

BiPAC 5200S RC Series

Бренд: Billion Страницы: 79

Бренд: Ubiquiti Страницы: 20

Бренд: Milesight Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды