Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 264 | Manualshive

Страница: 264 / 444

background image

Configuration Commands

Page 264

7750 SR OS Interface Configuration Guide

"ESS". The value does not change when the encap-type changes. The J1 string contains all zeros for a
non-provisioned path.

Parameters

trace-string —

Specifies either a string up to 62 bytes for SONET or 15 bytes for SDH. If the string

contains spaces, enclose it in quotation marks.

keepalive

Syntax

keepalive

time-interval

no keepalive

Context

config>port>sonet-sdh>path>cisco-hdlc
config>port>tdm>ds1>channel-group>cisco-hdlc
config>port>tdm>ds3>cisco-hdlc
config>port>tdm>e1>channel-group>cisco-hdlc
config>port>tdm>e3>cisco-hdlc

Description

This command specifies the interval, in seconds, used to send periodic keepalive packets. The
receiver process expects to receive a keepalive packet every "keepalive interval". The link is
declared down if the receiver process does not receive a keepalive within the "timeout interval". The
link is declared up once the number of continual keepalive packets received equals to the up-count.
The nodes at the two endpoints of the cHDLC link should be provisioned with the same values.

Default

10

Parameters

time-interval —

Specifies the interval used to send periodic keepalive packets.

Values

0 — 300 seconds. A value of 0 means no keepalive packets are sent.

up-count

Syntax

up-count

up-count

no up-count

Context

config>port>sonet-sdh>path>cisco-hdlc
config>port>tdm>ds1>channel-group>cisco-hdlc
config>port>tdm>ds3>cisco-hdlc
config>port>tdm>e1>channel-group>cisco-hdlc
config>port>tdm>e3>cisco-hdlc

Description

This command configures the number of continual keepalive packets that have to be received in order
to declare the link up. It is expected that the nodes at the two endpoints of the cHDLC link are
provisioned with the same values.

Default

1

Parameters

up-count —

Specifies the number of continual keepalive packets that have to be received in order to

declare the link up.

Values

1 — 3

«
...
262
263
264
265
266
...
»

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7750 SR OS

Бренд: Linksys Страницы: 2

Бренд: Abocom Страницы: 1

Бренд: Dahua Страницы: 24

InterReach Fusion SingleStar

Бренд: LGC wireless Страницы: 154

Бренд: Teknim Страницы: 10

Бренд: Eneo Страницы: 68

Бренд: 3Com Страницы: 32

Бренд: ANEP Страницы: 48

Бренд: Zhone Страницы: 53

Бренд: Ezviz Страницы: 38

Бренд: INFRALAN SECURITY Страницы: 15

Бренд: Brother Страницы: 251

Бренд: TRENDnet Страницы: 58

Бренд: Edimax Страницы: 29

Бренд: ORiNG Страницы: 2

Бренд: ORiNG Страницы: 2

IES-P3073GC Series

Бренд: ORiNG Страницы: 103

Бренд: Juniper Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды