Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 257 | Manualshive

Страница: 257 / 444

background image

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 257

Description

This command configures the speed of a SONET/SDH port as either OC3 or OC12. The framer for
this MDA operates in groups of four. Changing the port speed for a port requires resetting the framer
and causes a slight disruption on all four ports. The first framer controls ports 1,2,3,4, the second
framer controls ports 5,6,7,8 etc.

To change the port speed on a SONET/SDH port, the port must be administratively shut down and all
channels must be removed. When the port speed is changed, the default channel configuration is
recreated.

The

no

form of this command reverts back to default.

Default

oc12

Parameters

oc3 —

set the speed of the port to OC-3.

oc12 —

Set the speed of the port to OC-12.

threshold

Syntax

threshold

{

ber-sd

|

ber-sf

}

rate

threshold-rate

no threshold

{

ber-sd

|

ber-sf

}

Context

config>port>sonet-sdh

Description

This command configures the line signal degradation bit error rate (BER) and line signal failure
thresholds.

Line signal (b2) bit interleaved parity error rates are measured and when they cross either the
degradation or failure thresholds alarms are raised (see the report-alarm line & section command),
furthermore if the failure threshold is crossed the link will be set to operationally down.

Note:

For APS configurations, if the

ber-sd

or

ber-sf

threshold rates must be modified, the changes

must be performed at the line level on both the working and protect APS port member. See port

.

The

no

form of this command reverts to the default value.

Default

threshold ber-sf 6

— Signal degrade BER threshold of 10

-6

threshold ber-sf 3

— Signal failure BER threshold of 10

-3

Parameters

ber-sd —

Specifies the BER that specifies signal degradation

ber-sf —

Specifies the BER that specifies signal failure

rate —

The BER negative exponent (n in 10

-n

), expressed as a decimal integer.

Values

3 — 9 (10

-3

— 10

-9

)

«
...
255
256
257
258
259
...
»

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7750 SR OS

Бренд: 2N Страницы: 11

Бренд: 2N Страницы: 5

Бренд: 2N Telekomunikace Страницы: 24

Бренд: Rain Bird Страницы: 17

Бренд: Paradyne Страницы: 112

Бренд: Cambium Networks Страницы: 215

FieldPoint FP-3000

Бренд: National Instruments Страницы: 118

Compact NVR-AS 4000

Бренд: IndigoVision Страницы: 38

3C8567 - SuperStack II NETBuilder SI 567...

Бренд: 3Com Страницы: 6

Бренд: ZyXEL Communications Страницы: 170

Бренд: Perle Страницы: 491

802.11a/b/g SDIO WiFi Module SDM3100

Бренд: Abocom Страницы: 14

Бренд: Teldat Страницы: 23

Бренд: Ubiquiti Страницы: 20

i.LON SmartServer

Бренд: Echelon Страницы: 34

CentreCOM AT-3716XL

Бренд: Allied Telesis Страницы: 2

Бренд: C&H Technologies Страницы: 50

Бренд: Teldat Страницы: 47

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды