Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 412

Страница: 412 / 444

Show Commands

Page 412

7750 SR OS Interface Configuration Guide

port-connection

Syntax

port-connection

[

detail

]

Context

show>multilink-bundle>ima>atm

Description

This command displays port connection information.

Parameters

detail —

Displays detailed information.

Output

Show Mutlilink-Bundle IMA ATM Port-Connection Output —

The following table describes

show multilink-bundle IMA ATM port-connection output fields.

Mutlilink-Bundle IMA ATM Port-Connection Output Fields

Sample Output

A:NS052651098# show multilink-bundle bundle-ima-1/1.1 ima atm port-connection

==============================================================================

ATM Port Connection

==============================================================================

Port Id : bundle-ima-1/1.1

Admin State : up Oper state : up

Owner : SAP

Endpoint Type : Port Cast Type : P2P

Ing. Td Idx : 2 Egr. Td Idx : 2

Last Changed : 01/16/2007 14:24:00

==============================================================================

A:NS052651098#

Label

Description

Port ID

Displays the port ID for this bundle.

Admin State

ima —

Indicates that the bundle is of type IMA group.

Down —

The bundle is administratively down.

Oper State

Up —

The bundle is operationally up.

Down —

The bundle is operationally down.

Owner

Identifies the system entity that owns a specific ATM connection.

Endpoint Type

Displays the endpoint type.

Cast Type

Indicates the connection topology type.

Ing. Td Idx

Specifies the ATM traffic descriptor profile that applies to the receive
direction of the interface connection.

Egr. Td Idx

Specifies the ATM traffic descriptor profile that applies to the transmit
direction of the interface connection.

Last Changed

Indicates the date and time when the interface connection entered its
current operational state.

Содержание 7750 SR OS





























































































































































































































































































































































































































































Результаты поиска

Содержание 7750 SR OS

Отзывы:

Alcatel-Lucent 7750 SR OS, Руководство по настройке интерфейса, Страница: 412 / 444

Результаты поиска

Содержание 7750 SR OS

Отзывы: