Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 245 | Manualshive

Страница: 245 / 444

background image

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 245

Values

ip-address, global-mac-address

Default

Bundle type

Default

Physical MLPPP bundle

ieee802dot1GlobalMacAddress

MLPPP bundle protection group

IP address

discriminator-id

discriminator-id

—

Specifies the endpoint discriminator identifier value within the

specified endpoint-discriminator class. The values below are only for the ip-address class.

Values

Any valid IP address.

qos-profile

Syntax

qos-profile

profile-id

no qos-profile

Context

config>port>ml-bundle>mlppp>ingress

Description

This command specifies the ingress QoS profile to be used for the incoming traffic over this MLPPP
bundle.

Parameters

profile-id —

Specifies the ingress QoS profile to be used for the incoming traffic over this MLPPP

bundle. The value can only be modified if the bundle is shutdown.

Values

1 — 128

multiclass

Syntax

multiclass

count

no multiclass

Context

config>port>ml-bundle>multiclass

Description

This command enables multi-class MLPPP as defined by RFC 2686

, The Multi-Class Extension to

Multi-Link PPP

, on a MLPPP bundle (including MLPPP bundle protection groups) with 2, 3 or 4

classes. For multiclass MLPPP bundles with a non-zero count, the class index takes valid values from
0 to one less than the maximum number of classes inclusive. For example a 4-class MLPPP bundle
has 4 classes with indices 0, 1, 2, and 3. A bundle must be shutdown with no links for this value to be
changed.

Entries are created and deleted by the system depending on the number of classes being used by a
given MLPPP bundle.

The

no

form of the command disables multi-class MLPPP.

Default

4

Parameters

count —

Specifies the number of classes in a MLPPP bundle.

Values

2 — 4

«
...
243
244
245
246
247
...
»

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7750 SR OS

Бренд: Draytek Страницы: 8

Бренд: Patton electronics Страницы: 12

NetIron MLXe Series

Бренд: Brocade Communications Systems Страницы: 305

Easy Tool-ID BSG TID-05-T30-00-005

Бренд: Balluff Страницы: 46

memonizerWORKSTATION

Бренд: MEMON Страницы: 2

VMG5313-BXB SERIES

Бренд: ZyXEL Communications Страницы: 2

Бренд: TP-Link Страницы: 16

Safeguard for Privileged Sessions 3000

Бренд: One Identity Страницы: 37

CU8210-D001-0200

Бренд: Beckhoff Страницы: 25

Бренд: Ubiquiti Страницы: 32

Passport WDXML1000UE

Бренд: Western Digital Страницы: 2

Бренд: IBM Страницы: 70

Бренд: B&B Electronics Страницы: 19

Бренд: IntraServer Technology Страницы: 16

Бренд: Technicolor Delivery Technologies Страницы: 76

Бренд: Viking Страницы: 8

Бренд: Advantech Страницы: 44

SwyxConnect 1722

Бренд: Swyx Страницы: 112

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды