Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 220 | Manualshive

Страница: 220 / 444

background image

Configuration Commands

Page 220

7750 SR OS Interface Configuration Guide

When a port is being configured as a working circuit of an APS group, all common configuration as
described above and all service configurations related to the APS port is operationally inherited by
the working circuit from the aps-

group-id

. If the working circuit cannot inherit that configuration, for

example, due to resource limitations, the configuration attempt fails and an error is returned to the
user.

Before a working circuit can be removed from an APS group, the working circuit port must be
shutdown. The inherited configuration for the circuit and APS operational commands for that circuit
are not preserved when the circuit is removed from the APS group.

Note that all configurations for aps-

group-id

under the

config>port

context and its submenus and all

configuration for services that use this aps-

group-id

is preserved as a non-activated configuration

since the APS group no longer has any physical circuits assigned.

The

no

form of this command removes the working-circuit. The working circuit can only be removed

from the configuration after the protect circuit has been removed.

Default

none

Parameters

port-id —

Specify the physical port that will act as the working circuit for this APS group.

Syntax

:

port-id

:

slot/mda/port

Modifying Hold-Down Timer Values

Note that for APS configurations, the

hold-time down

hold-time up

default values are 100 ms

and 500 ms respectively. But, if there is a large difference in the transmission delay between the APS
working (

working-circuit

) and protect line (

protect-circuit

), it is highly suggested to increase the

default timer on the working line accordingly with the transmission delay present on the protect line.
See

on

The following output shows an example of the timers on POS interfaces.

A:NS044050253# show port aps-1

===============================================================================

SONET/SDH Interface

===============================================================================

Description : APS Group

Interface : aps-1 Speed : oc3

Admin Status : up Oper Status : up

Physical Link : Yes Loopback Mode : none

Single Fiber Mode : No

Clock Source : node Framing : sonet

Last State Change : 04/11/2007 13:53:01 Port IfIndex : 1358987264

J0 String : 2/1/5 7750-SR-7 Section Trace Mode : string

Rx S1 Byte : 0x00 Rx K1/K2 Byte : 0x00/0x00

Rx J0 String (Hex) : 81 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

Cfg Alarm : loc lais lrdi ss1f lb2er-sd lb2er-sf slof slos lrei

Alarm Status :

Hold time up : 500 milliseconds

Hold time down : 100 milliseconds

===============================================================================

Port Statistics

===============================================================================

Input Output

-------------------------------------------------------------------------------

Packets 6670498 3804661

«
...
218
219
220
221
222
...
»

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7750 SR OS

Бренд: Patton electronics Страницы: 75

RocketLink-G 3088/I

Бренд: Patton electronics Страницы: 61

Бренд: Patton Страницы: 12

Бренд: Patton Страницы: 84

OnSite 3210 Series

Бренд: Patton Страницы: 110

Бренд: Patton electronics Страницы: 2

SMARTNODE 4110 Series

Бренд: Patton electronics Страницы: 78

Бренд: Patton electronics Страницы: 8

Firebox SOHO 6 Wireless

Бренд: Watchguard Страницы: 8

Бренд: IEI Technology Страницы: 86

Lite N42B1P Series

Бренд: Dahua Technology Страницы: 14

Бренд: Baicells Страницы: 10

Бренд: Kohler Страницы: 32

Бренд: IEI Technology Страницы: 2

Бренд: Xantech Страницы: 5

Бренд: Ubiquiti Страницы: 20

Бренд: Milesight Страницы: 15

TE100S8P - Fast Ethernet Switch

Бренд: TRENDnet Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды