Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 237 | Manualshive

Страница: 237 / 444

Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 237

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 237

Values

1 — 9000

re-authentication

Syntax

[

no

]

re-authentication

Context

config>port>ethernet>dot1x

Description

This command enables / disables periodic 802.1x re-authentication.

When re-authentication is enabled, the 7750 SR will re-authenticate clients on the port every re-auth-
period seconds.

The

no

form of the command returns the value to the default.

Default

re-authentication

server-timeout

Syntax

server-timeout

seconds

no server-timeout

Context

config>port>ethernet>dot1x

Description

This command configures the period during which the 7750 SR waits for the RADIUS server to
responds to its AccessRequest message. When this timer expires, the 7750 SR will re-send the
AccessRequest message, up to max-request-number times.

The

no

form of this command returns the value to the default.

Default

30

Parameters

seconds —

The server timeout period in seconds.

Values

1 — 300

supplicant-timeout

Syntax

supplicant-timeout

seconds

no supplicant-timeout

Context

config>port>ethernet>dot1x

Description

This command configures the period during which the 7750 SR waits for a client to respond to its
EAPOL messages. When the supplicant-timeout expires, the 802.1x authentication session is
considered to have failed.

The

no

form of this command returns the value to the default.

Default

30

«
...
235
236
237
238
239
...
»

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов