Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 326

Страница: 326 / 444

Show Commands

Page 326

7750 SR OS Interface Configuration Guide

CPM Output —

The following table describes the output fields for a CPM card.

Label

Description

Slot

The slot of the card in the chassis.

Card Provisioned

The SF/CPM type that is configured for the slot.

Card Equipped

The SF/CPM type that is actually populated in the slot.

Admin State

Up —

The SF/CPM is administratively up.

Down —

The SF/CPM is administratively down.

Operational

State

Up —

The SF/CPM is operationally up.

Down —

The SF/CPM is operationally down.

BOF last modified

The date and time of the most recent BOF modification.

Config file ver-

sion

The configuration file version.

Config file last

modified

The date and time of the most recent config file modification.

Config file last

modified

The date and time of the most recent config file modification.

Config file last

saved

The date and time of the most recent config file save.

CPM card status

active —

The card is acting as the primary (active) CPM in a

redundant system.

standby —

The card is acting as the standby (secondary) CPM in a

redundant system.

Administrative

state

Up —

The CPM is administratively up.

Down —

The CPM is administratively down.

Operational

state

Up —

The CPM is operationally up.

Down —

The CPM is operationally down.

Serial number

The compact flash part number. Not user modifiable.

Firmware revi-

sion

The firmware version. Not user modifiable.

Model number

The compact flash model number. Not user modifiable.

Size

The amount of space available on the compact flash card.

Free space

The amount of space remaining on the compact flash card.

Part number

The SF/CPM part number.

Содержание 7750 SR OS





























































































































































































































































































































































































































































Результаты поиска

Содержание 7750 SR OS

Отзывы:

Похожие инструкции для 7750 SR OS

Бренды по названию

Популярные бренды

Alcatel-Lucent 7750 SR OS, Руководство по настройке интерфейса

Результаты поиска

Содержание 7750 SR OS

Отзывы:

Похожие инструкции для 7750 SR OS

Бренды по названию

Популярные бренды