Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 281 | Manualshive

Страница: 281 / 444

background image

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 281

32 —

Use 32 bit checksum for the associated port/channel.

down-count

Syntax

down-count

down-coun

t

no down-count

Context

config>port>sonet-sdh>path>cisco-hdlc
config>port>tdm>ds1>channel-group>cisco-hdlc
config>port>tdm>ds3>cisco-hdlc
config>port>tdm>e1>channel-group>cisco-hdlc
config>port>tdm>e3>cisco-hdlc

Description

This command configures the number of keepalive intervals that must pass without receiving a
keepalive packet before the link is declared down. It is expected that the nodes at the two endpoints of
the cHDLC link are provisioned with the same values.

Default

3

down-count —

Specifies the number of keep alive intervals that must pass without receiving a keep

alive packet before the link is declared down.

Values

3 — 16

encap-type

Syntax

encap-type

{

atm

|

bcp-null

|

bcp-dot1q

|

ipcp

|

ppp-auto

|

frame-relay

|

wan-mirror

|cisco-hdlc| cem

}

Context

config>port>tdm>ds1>channel-group
config>port>tdm>ds3
config>port>tdm>e1>channel-group
config>port>tdm>e3

Description

This command configures the encapsulation method used to on the specified port, path, or channel.
This parameter can be set on both access and network ports.

When the

encap-type

is set to ATM the CRC, timeslots, scrambling (if applicable), and idle-cycle-

flags are set to ATM defaults respectively. When the encap-type is changed from ATM, those
parameters are set to their non-ATM defaults.

When the

encap-type

is ATM, ATM sub-layer verification (GR-1248-CORE,

Generic Requirements

for Operations of ATM Network Elements (NEs)

) is automatically enabled. When ATM PLCP cell

mapping is used, the results of this verification include:

• PLCP Severely Errored Framing Seconds

• PLCP Alarm State

• PLCP Unavailable Seconds Counter

When ATM direct cell mapping is used, the result of the verification includes:

«
...
279
280
281
282
283
...
»

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7750 SR OS

Univerge SV8100

Бренд: NEC Страницы: 44

Ray 3 Plus Client

Бренд: Sun Microsystems Страницы: 6

Бренд: Paradyne Страницы: 11

Бренд: Paradyne Страницы: 19

Бренд: Paradyne Страницы: 32

COMSPHERE 3550 Series

Бренд: Paradyne Страницы: 153

Jetstream CPX-1000

Бренд: Paradyne Страницы: 141

FrameSaver 9783

Бренд: Paradyne Страницы: 28

COMSPHERE 6800 Series

Бренд: Paradyne Страницы: 7

Бренд: iDirect Страницы: 52

Бренд: NETGEAR Страницы: 2

Бренд: insys icom Страницы: 4

Бренд: Belkin Страницы: 2

Бренд: Watchguard Страницы: 21

VAR-SOM-MX8M-PLUS

Бренд: Variscite Страницы: 2

Бренд: Hi-flying Страницы: 59

DTS 4020.timebridge

Бренд: Mobatime Страницы: 94

Бренд: Pro-Nets Technology Corporation Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды