Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 444

Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 12

Preface

Page 12

7750 SR OS Interface Configuration Guide

This guide describes card, Media Dependent Adapter (MDA), and port provisioning.

•

7750 SR OS Router Configuration Guide

This guide describes logical IP routing interfaces and associated attributes such as an IP
address, port, link aggregation group (LAG) as well as IP and MAC-based filtering,
VRRP, and Cflowd.

•

7750 SR OS Routing Protocols Guide

This guide provides an overview of routing concepts and provides configuration examples
for RIP, OSPF, IS-IS, Multicast, BGP, and route policies.

•

7750 SR OS MPLS Guide

This guide describes how to configure Multiprotocol Label Switching (MPLS) and Label
Distribution Protocol (LDP).

•

7750 SR OS Services Guide

This guide describes how to configure service parameters such as service distribution
points (SDPs), customer information, and user services.

•

7750 SR OS OAM and Diagnostic Guide

This guide describes how to configure service parameters such as service mirroring and
Operations, Administration and Management (OAM) tools.

•

7750 SR OS Triple Play Guide

This guide describes Triple Play services and support provided by the 7750 SR and
presents examples to configure and implement various protocols and services.

•

7750 SR Quality of Service Guide

This guide describes how to configure Quality of Service (QoS) policy management.

•

7750 SR-Series OS Integrated Services Adapter Guide
This guide describes Triple Play and subscriber management services and how these are
linked to Application Assurance.
Note that this guide explains details and discusses Application Assurance functionality.
The Triple Play Guide contains only information on how subscribers are associated with
Application Assurance.

«
...
10
11
12
13
14
...
»

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов