Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 71 | Manualshive

Страница: 71 / 444

background image

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 71

Configuring LAGs

LAG configuration guidelines include:

•

When preprovisioning chassis slots, cards, MDAs, and Ethernet ports, distribute the LAG
ports for a given LAG over as many slots and MDAs as possible. This minimizes the
impact that a slot or MDA failure has on the performance of the LAG.

•

A maximum of 200 LAGs, eight ports in each, can be configured on a 7750 SR. The 7750
SR-1 supports a maximum of 64 LAGs.

•

Ports can be added or removed from the LAG while the LAG and its ports (other than the
port being removed) remain operational. When ports to and/or from the LAG are added or
removed, the hashing algorithm is adjusted for the new port count.

•

show

commands display physical port statistics on a port-by-port basis or the entire LAG

can be displayed.

•

LAG is supported on Ethernet ports.

•

Ports of a particular LAG can be of different types but they must be the same speed and
duplex. To guarantee the same port speed is used for all ports in a LAG, autonegotiation
must be disabled or in limited mode to ensure only a specific speed is advertised. For
10GBE ports, the xgig setting must be set to the same value.

displays traffic routed between ALA-1 and ALA-2 as a LAG consisting of four ports.

Figure 14: LAG Configuration

OSSG011

ALA-1

ALA-4

ALA-2

LAG-1

LAG-2

ALA-3

«
...
69
70
71
72
73
...
»

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7750 SR OS

Бренд: IBM Страницы: 248

Бренд: Makita Страницы: 2

Бренд: Hama Страницы: 10

Бренд: ICP DAS USA Страницы: 14

Бренд: ICP DAS USA Страницы: 25

Бренд: ICP DAS USA Страницы: 15

Бренд: ICP Страницы: 14

Бренд: National Instruments Страницы: 162

Бренд: Ubiquiti Страницы: 50

Бренд: NETGEAR Страницы: 2

Бренд: QuickLink Страницы: 8

Бренд: B&B Electronics Страницы: 2

Бренд: Z-Com Страницы: 18

Бренд: ZoneVu Страницы: 15

Comet 3356P-LAN

Бренд: ZyXEL Communications Страницы: 38

Бренд: Multi-Link Страницы: 31

Бренд: MicroNova Страницы: 113

Бренд: Sharedband Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды