manualshive.com logo in svg

Alcatel-Lucent 7750 SR OS, Руководство по настройке интерфейса, Страница: 65 / 444

Поделиться
Скачать
Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 65

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 65

An example of the customer application in the mobile market is displayed in 

Figure 13

. 

Figure 13: MC-APS with ATM VLL Redundancy 

In the application show in 

Figure 12

, 2G and 3G cell sites are aggregated into a Tier 2 or Tier 3 

hub site before being backhauled to a Tier 1 site where the radio network controller (RNC) which 
terminates user calls is located. This application combines MC-APS on the RNC access side and 
pseudowire redundancy and pseudowire switching on the core network side. pseudowire 
switching is used in order to separate the routing domains between the access network and the core 
network.

OSSG145

GSM/GPRS

HSxPA

R99

ATM

Switch

E1 TDM

E1 ATM
E1 IMA ATM

E1 IMA ATM
Or xDSL

7750

SR-7

IP MPL Core

Layer 3 VPNs

Convergent

Packet Network

RNC Cluster

PW

T-PE

Active/Standby

Pseudo-wire

Multi-chassis

Protection

Pseudo-wire
Segments

T-PE

S-PE

7750

SR-7

7750

SR-7

7750

SR-7

7750

SR-7

PW

PW

PW

PW

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов